background image

3

Important Safety Information

Throughout this manual, notices appear to bring your attention to situations which could 
result in death, serious injury, or damage to the unit. 

 WARNING  

Indicates a hazardous situation which could result in death or 
serious injury. 

CAUTION 

Indicates a situation which could result in damage to the unit.

IMPORTANT 

Indicates important information about the use and care of the 
unit.

 WARNING

This icemaker should be destined only to the use for which it has been 
expressly conceived. Any other use should be considered improper and 
therefore dangerous. The manufacturer cannot be held responsible for 
eventual damage caused by improper, incorrect, and unreasonable use.

To reduce the risk of death, electric shock, serious injury, or fire, follow 
basic precautions including the following:

• This unit requires an independent power supply. See the nameplate for 

proper voltage and breaker/fuse size. Failure to use a proper breaker or fuse 
can result in a tripped breaker, blown fuses, or damage to existing wiring. 
This could lead to heat generation or fire.

• 

THIS APPLIANCE MUST BE GROUNDED:

 

This unit is equipped with a 

3-prong grounding plug to reduce the risk of potential shock hazards. It must 
be plugged into a properly grounded wall outlet. If the outlet is a -prong 
outlet, it is your personal responsibility to have a qualified electrician replace 
it with a properly grounded 3-prong outlet. Do not remove the ground prong 
from the power cord and do not use an adapter plug.

• Do not use an extension cord.
• Make sure the power switch is off before plugging in or unplugging the unit to 

reduce the risk of electric shock.

• Do not damage the power cord. It should not be altered, jerked, bundled, 

weighed down, pinched, or tangled. Such actions could result in electric 
shock or fire. To unplug the unit, be sure to pull the plug, not the cord, and 
do not jerk the cord.

• To reduce the risk of electric shock, do not touch the plug or power switch 

with damp hands.

• Do not place fingers or any other objects into the ice discharge opening.
• This unit should be disassembled or repaired only by qualified service 

personnel to reduce the risk of electric shock, injury, or fire.

• Do not make any alterations to the unit. Alterations could result in electric 

shock, injury, fire, or damage to the unit.

Содержание C-100BAE-AD
























Отзывы: