Hornet 732T Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 22

Hornet 732T Скачать руководство пользователя страница 9

© 1995,1997 Directed Electronics, Inc. Vista, CA

9

N432 1-98.PM6

WIRE CONNECTION GUIDE

WIRE CONNECTION GUIDE

H1/1 ORANGE (-) ground-when-armed output: This wire supplies a (-) 500 mA ground as long as the system is armed.
This output ceases as soon as the system is disarmed. The orange wire is pre-wired to control the 8618 starter kill
relay.

NOTE: If connecting the ORANGE wire to control another module, such as a 529T or 530T window controller,
a 1 amp diode (type 1N4004) will be required. Insert the diode as shown below.

H1/2 WHITE (+) light flash output: This wire should be connected to the (+) parking light wire, as described in the
“Finding the wires you need” section of this manual. This output is protected with a 7.5 amp fuse. Never increase the
value of the light flash fuse. If more current is required, use an external relay.

H1/3 WHITE/BLUE channel 3 (-) output: This wire provides a (-) 200 mA signal whenever the transmitter code
controlling channel 3 is received. This signal will continue as long as that transmission is received. Use for options such
as the 551T Valet

®

Start system, the 529T or 530T power window controllers, etc.

IMPORTANT! Never use this wire to drive anything but a relay or a low-current input! The transistorized output
can only provide 200 mA of current, and connecting directly to a solenoid, motor, or other high-current device
will cause it to fail.

H1/4 BLACK/WHITE (-) 200 mA domelight-supervision output: Connect this wire to the optional domelight
supervision relay as shown below:

IMPORTANT! This output is only intended to drive a relay. It cannot be connected directly to the domelight
circuit, as the output cannot support the current draw of one or more light bulbs.

BLACK

GREEN

TO STARTER MOTOR

X

X

ORANGE

IGNITION SWITCH

1N4004 DIODE

PRE-WIRED

STARTER KILL

RELAY

ORANGE (-)

WHEN-ARMED

OUTPUT

TO OPTIONAL
SENSORS, 529T,
530T, ETC.

CONTROL

UNIT

IMPORTANT! Never interrupt any wire other than the starter wire.

cccc

H1/4 BLACK/WHITE

(+) 12V

CONSTANT FUSED

(-) CHASSIS GROUND IF

DOORS ARE (-) SWITCHED,

(+) 12V IF DOORS ARE

(+) SWITCHED

H1/5 GREEN (-) DOOR INPUT

OR

H1/7 VIOLET (+) DOOR INPUT

WHITE H1/2

(+) LIGHT FLASH OUTPUT

(+) YELLOW SWITCHED IGNITION

YELLOW

«
...
7
8
9
10
11
...
»

Содержание 732T























Отзывы:

Нет отзывов