Hornet 732T Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 22

Hornet 732T Скачать руководство пользователя страница 10

© 1995,1997 Directed Electronics, Inc. Vista, CA

10

N432 1-98.PM6

H1/5 GREEN (-) door trigger or H1/7 VIOLET (+) door trigger input: If the door switch wire you found is (-) when the
door is open, connect the GREEN wire to it. If the door switch wire you found is (+) when the door is open, use the
VIOLET wire instead.

IMPORTANT! Test to make sure this wire "sees" all doors!

H1/6 BLUE (-) Multiplex trigger input: This input is capable of triggering either the Warn Away

®

response or the

triggered sequence. Inputs that are shorter than .8 seconds will only trigger the Warn Away

®

response. The first stage

of all DEI

®

dual stage sensors supply this type of pulse. Inputs that are longer than .8 seconds will trigger the full alarm

cycle. The second stage output of DEI

®

dual stage sensors supply this type of pulse. Connecting this input to a hood

or trunk pin switch will also trigger the full alarm response.

H1/8 BLACK (-) chassis ground connection. Connect this wire to bare metal, preferably with a factory bolt rather than
your own screw (screws tend to either strip or loosen with time). We recommend grounding all your components to
the same point in the vehicle.

NOTE: Remove any paint below ring connector.

H1/9 YELLOW (+) ignition input. Connect this wire to an ignition wire as described on page 5. This wire must show
+12V with the key in run position and during cranking. Take great care that this wire cannot be shorted to the chassis
at any point.

H1/10 BROWN (+) siren output: Connect this to the red wire of the 514T Revenger™ siren. Connect the black wire of
the siren to (-) chassis ground, preferably at the same point you grounded the control module’s H1/8 BLACK wire.

«
...
8
9
10
11
12
...
»

Содержание 732T























Отзывы:

Нет отзывов