Hornet 732T Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

Hornet 732T Скачать руководство пользователя страница 11

© 1995,1997 Directed Electronics, Inc. Vista, CA

11

N432 1-98.PM6

H1/11 RED (+)12V constant power input: Before connecting this wire, remove the supplied fuse. Connect to the battery
positive terminal or the constant 12V supply to the ignition switch as described on Page 5.

NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 10A fuse in the
harness for this purpose. This fuse protects the module itself.

H1/12 RED/WHITE channel 2, 200mA (-) output: When the system receives the code controlling channel, for longer
than 1.5 seconds, the red/white will supply an output as long as the transmission continues. This is often used to
operate a trunk/hatch release or other relay-driven function.

NOTE: If an instant output is desired, press Button I & II at the same time

IMPORTANT! Never use this wire to drive anything but a relay or a low-current input! The transistorized output
can only supply 200 mA of current, connecting directly to a solenoid, motor, or other high-current device will
cause it to fail.

(+) 12V CONSTANT FUSED

RED/WHITE H1/1
FUNCTION 2 OUTPUT

(+)12V IF (+) SWITCHED
(-) GROUND IF (-) SWITCHED

SWITCHED TRUNK RELEASE WIRE

87

87A

85

86

30

RED/WHITE H1/12

CHANNEL 2 OUTPUT

PLUG-IN LED AND VALET

®

/ PROGRAM SWITCH

These plug into the module. The Status LED plugs into the small two-pin socket, while the Valet

®

/Program Switch

should be plugged into the larger blue two-pin connector. The Status LED fits in a 9/32" hole.

Status LED

Valet

®

/Program Switch

ON-BOARD STINGER

™

DOUBLE GUARD

™

SHOCK SENSOR

There is a full-fledged Stinger

™

shock sensor inside the control unit. Adjustments are made via the rotary control as

indicated above. Since the Stinger

™

shock sensor does not work well when mounted too firmly to metal, we

recommend

against screwing down the control module.

NOTE: When adjusting the sensor, it must be in the same mounting location that it will be after the install is
completed. Adjusting the sensor and then relocating the module requires readjustment.

É

Less sensitive

Ê

More sensitive

«
...
9
10
11
12
13
...
»

Содержание 732T























Отзывы:

Нет отзывов