manualshive.com logo in svg

Hornet 732T, Руководство по установке, Страница: 16 / 22

Поделиться
Скачать
Hornet 732T Скачать руководство пользователя страница 16

© 1995,1997 Directed Electronics, Inc. Vista, CA

16

N432 1-98.PM6

TRANSMITTER/RECEIVER LEARN ROUTINE™

In order to enter Learn Routine™ the Valet

® 

/Program button must be plugged into the blue port. There is a basic

sequence to remember whenever programming this unit:  Door, Key, Choose, Transmit and Release.

1. 

Door

Open a door. Either the H1/5 GREEN  or the H1/7 VIOLET door
trigger wire must be connected for the control unit to “see” an
open door.

2. 

Key

Turn the ignition on to the run position. The H1/9 YELLOW
switched ignition input must be connected.

3. 

Choose

Within 15 seconds, press and release the momentary button
to select the channel you wish to program:

Press and Release

To Program

Press and Release

To Program

One time

Arm/disarm/panic

Two times

Channel two output

(Silent Mode™/Remote Valet

® 

)

Three times

Channel three output

NOTE: When programming a transmitter button to step three, the assigned button will provide an

instant output on the red/white wire.

Once you have selected the step, press the button once more and hold it.  The unit will chirp one, two
or three times depending on the channel selected. Do not release the momentary button.

4. 

Transmit

While holding the momentary button, press the button on the transmitter  that
you would like to control the selected receiver channel. One chirp will confirm
that the code has been learned.

5. 

Release

Once the code is learned, the button can be released.

You can step from one step to another by releasing the Valet

®

 /program button and tapping it to advance steps

and then holding it. For instance: You have programmed channel one and you want to program channel two.
Release the Valet

®

 /program button.  Press it one time and release it to advance from step one to step two.  Now,

press and hold the button down and the unit will chirp twice.  As before, do not release it.

If you want to program channel two (instant) after programming channel one, release the momentary button press it
twice and release it to advance to step three. Then press it once more and hold it. The siren will chirp three times to
confirm it is ready to receive the code from the transmitter.

Learn Routine

™

 will be exited if:

•

Ignition is turned off

•

Door is closed

•

Program button is pressed too many times

•

More than 15 seconds elapses between steps

One long chirp indicates that Learn Routine

™

 has been exited

Содержание 732T























Отзывы:

Нет отзывов