Hornet 732T Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 22

Hornet 732T Скачать руководство пользователя страница 18

© 1995,1997 Directed Electronics, Inc. Vista, CA

18

N432 1-98.PM6

OPERATING-SETTINGS LEARN ROUTINE™

Many of the operating settings of this unit are programmable. They can be changed whenever necessary through a
computer-based Learn Routine™. The Valet

®

/program push-button switch, plugged into the blue port is used together

with a programmed transmitter to change the settings. To program settings remember: Door, Key, Choose, Transmit
and Release.

1.

Door

Open a door. Either the H1/5 GREEN or the H1/7 VIOLET door
trigger wire must be connected for the control unit to “see” an
open door.

2.

Key

Turn the ignition on and then back off. The H1/9 YELLOW
switched ignition input must be connected.

3.

Choose

Within 15 seconds, press and release the Valet

®

/Program

button the number of times corresponding to the number of
the desired feature (see the chart below). The one chirp
settings below are the factory default settings, except where
indicated by bold text.

Feature Number

One-chirp Setting

Two-chirp Setting

1

Active arming

Passive arming

2

Arm/disarm chirps on

Arm/disarm chirps off

3

Ignition-controlled door locks

Standard door locks

4

Active locking only

Passive locking

5

Panic with ignition on

No panic with ignition on

6

0.8 second door lock pulses

3.5 second door lock pulses

7

Forced passive arming on

Forced passive arming off

8

Automatic engine disable on

Automatic engine disable off

9

Double pulse unlock off

Double pulse unlock on

10

Code-Hopping™ on

Code-Hopping™ off

11

Siren

Horn honk

«
...
16
17
18
19
20
...
»

Содержание 732T























Отзывы:

Нет отзывов