Horizon Hobby hobbyzone Carbon Cub S 2 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 38

Horizon Hobby hobbyzone Carbon Cub S 2 Скачать руководство пользователя страница 7

Carbon Cub S 2 1.3m

EN

7

AIL-R

AIL-L

2.5 X 10mm (6)

3 X 12mm (4)

Installation

The hardware for the wing installation is in bag C.

1. Connect the left aileron servo connector to the servo extension labeled

“

AIL-L

” and the right aileron servo connector to the servo extension labeled

“

AIL-R

”.

2. Align the wing in the wing saddle, aligning the holes in the wing cover with

the mounting holes in the fuselage. Ensure the flap linkages and servo

wires are fully within the fuselage opening.

NOTICE:

DO NOT crush or otherwise damage the wiring when attaching the

wing to the fuselage. Servo damage and loss of control may result.

3. Secure the assembled wing to the fuselage with four 3 x 12mm Phillips

screws using a PH#1 Phillips screwdriver.

4. Attach the right and left wing struts (marked R and L) under the wing and

fuselage using six Phillips screws and a PH#1 Phillips screwdriver.

Wing Alignment

Adjust the position of the four screws in the top of the strut slots so the wings

are not flexed down or twisted. The wings should be flat or have a slight

amount of dihedral from tip to tip, as shown in the illustration.

«
...
5
6
7
8
9
...
»

Содержание hobbyzone Carbon Cub S 2







































Отзывы:

Нет отзывов