manualshive.com logo in svg

Horizon Hobby hobbyzone Carbon Cub S 2, Инструкция по эксплуатации, Страница: 37 / 38

Поделиться
Скачать
Horizon Hobby hobbyzone Carbon Cub S 2 Скачать руководство пользователя страница 37

Carbon Cub S 2 1.3m

EN

37

IC Information

CAN ICES-3 (B)/NMB-3(B) 
Contains IC: 6157A-KATY1T
IC: 6157A-SRLRR2

This device contains license-exempt transmitter(s)/receivers(s) that comply 

with Innovation, Science, and Economic Development Canada’s license-exempt 

RSS(s). Operation is subject to the following 2 conditions: 

1.  This device may not cause interference.
2.  This device must accept any interference, including interference that may 

cause undesired operation of the device.

Compliance Information for the European Union

EU Compliance Statement:
HBZ Carbon Cub S 2 RTF Basic (HBZ320001)

:

 

Hereby, Horizon 

Hobby, LLC declares that the device is in compliance with the 

following: EU Radio Equipment Directive 2014/53/EU; RoHS 2 Directive 

2011/65/EU, RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863.

NOTE:

 This product contains batteries that are covered under the 2006/66/EC 

European Directive, which cannot be disposed of with normal household waste. 

Please follow local regulations.

HBZ Carbon Cub S 2 BNF Basic (HBZ32500)

:

 

Hereby, Horizon Hobby, 

LLC declares that the device is in compliance with the following: EU Radio 

Equipment Directive 2014/53/EU; RoHS 2 Directive 2011/65/EU, RoHS 3 

Directive - Amending 2011/65/EU Annex II 2015/863.
The full text of the EU declaration of conformity is available at the following 

internet address: https://www.horizonhobby.com/content/support-render-

compliance.

Wireless frequency and output:
Transmitter:

2402.0 - 2478.0MHz 

17.7 dBm

Receiver: 

2404–2476MHz 

3dBm

EU Manufacturer of Record:

Horizon Hobby, LLC 

2904 Research Road 

Champaign, IL 61822 USA

EU Importer of Record:

Horizon Hobby, GmbH 

Hanskampring 9 

22885 Barsbüttel Germany

WEEE NOTICE:

This appliance is labeled in accordance with European Directive 

2012/19/EU concerning waste of electrical and electronic 

equipment (WEEE). This label indicates that this product should not 

be disposed of with household waste. It should be deposited at an 

appropriate facility to enable recovery and recycling.

Содержание hobbyzone Carbon Cub S 2







































Отзывы:

Нет отзывов