Horizon Hobby hobbyzone Carbon Cub S 2 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 38

Horizon Hobby hobbyzone Carbon Cub S 2 Скачать руководство пользователя страница 11

Carbon Cub S 2 1.3m

EN

11

Transmitter

command

Control Surface Response

(viewed from the rear)

Elev

ator

Aileron

Rudder

Control Direction Test

WARNING:

Do not perform this or any other equipment test without

turning on throttle cut. Serious injury or property damage could result

from the motor starting inadvertently.

If the control surfaces do not respond as shown,

DO NOT FLY.

Refer to the

Troubleshooting Guide

for more information. If you need more assistance,

contact the appropriate Horizon Hobby Product Support department.

1. Power on the transmitter.
2. Turn on throttle cut (switch H, position 1).
3. Set the flight mode switch to Experienced Mode (switch B, position 2).

IMPORTANT:

Do NOT check the controls in the Beginner or Intermediate Modes

(switch B, position 0 or 1).

4. Place the model on level ground away from obstacles.
5. Power on the aircraft, and wait for it to fully initialize.
6. Move the sticks on the transmitter as shown in the table and observe the

control surfaces on the aircraft. Ensure the aircraft control surfaces respond

as shown and return to neutral when the control input is released.

7. Check for any binding in the control surfaces.
8. With the aircraft on a smooth surface, roll the aircraft forward by hand. Push

the rudder trim button on the transmitter left or right until the aircraft tracks

straight.

TIP:

The transmitter emits a faint beep with each click of the trim buttons in

either direction. Holding the button in either direction quickly adjusts the trim

several steps until the button is released or until the trim reaches the end of its

travel. If the trim button does not beep when clicked, the trim is at the far end

of its travel. Center trim is indicated by a slightly louder beep.

Centering the Control Surfaces

After checking for correct control surface movement, release the transmitter

sticks. Check each of the control surfaces to make sure they are centered.
For any surface that is not centered:

1. Slide the retaining sleeve off the clevis.
2. Gently pry the clevis open.
3. Slide the clevis pin out of the control horn.
4. Rotate the clevis on the pushrod to lengthen or shorten the length of the

pushrod to adjust the center position of the surface.

5. When the correct position is achieved, slide the clevis pin back into the

correct control horn hole.

6. Close the clevis, capturing the control horn between the sides.
7. Slide the retaining sleeve over the clevis to keep the clevis from opening.

Throttle/

Rudder Stick

Elevator/

Aileron Stick

«
...
9
10
11
12
13
...
»

Содержание hobbyzone Carbon Cub S 2







































Отзывы:

Нет отзывов