3
All accessories can be fitted to the hose handle or the end of the tubes.
2 in 1 Tool
combines several functions into one tool:
Crevice Tool
– For corners and hard to reach areas.
[12]
Dusting brush
– For bookshelves, frames, keyboards and other delicate areas.
[13]
Pet Hair Remover mini Turbo Nozzle*
- Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal.
[1X]
Allergen Remover mini Turbo Nozzle*
– Use the mini turbo nozzle on stairs or for
deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for
allergen removal.
[1y]
Hard Floor Nozzle*
– For parquet floors and other delicate floors.
[1Z]
ImPORTANT:
Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides
and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is
rotating.
ClEANER mAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust container.
ImPORTANT:
To maintain optimum performance, do not allow the dust to sit higher than
the max level.
1. Release the dust container by sliding the dust container release button towards the
front of the cleaner. Lift the dust container from the cleaner main body.
[14]
2. Before emptying the Dust Container, gently tap it against the side of a bin to release
any excess dust from the filter.
3. To empty the Dust Container, hold the Dust Container over a bin with one hand and
use the other hand to press the Dust Container Flap Opening Button to release the
dust into the bin.
[15]
4.
Close the Dust Container Flap and refit the Dust Container to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with a pre-motor and exhaust filter. To maintain optimum cleaning
performance, regularly clean the filters. Remove excess dust from the filters by gently
tapping them against the side of a bin. The filters should be washed after every 5
container empties.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean
your filters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
IMPORTANT: Regularly check and maintain the filters by following the filter
maintenance instructions, it is also recommended that you purchase new filters
after every 3rd filter wash. This will maintain your cleaners performance.
To access the Pre-Motor filter:
1. Empty the Dust Container as described in ‘Emptying the Dust Container’. Then,
keeping the Dust Container Flap open:
2.
Remove the pre-motor filter by rotating it clockwise at the bottom of the Dust
Container.
[16]
3.
Separate the protective mesh from the filter.
[17]
Gently tap both the protective
mesh and the filter against the side of a bin to remove excess dust and wash both
of them under warm water.
[18]
Do not use hot water or detergents.
4.
Remove excess water from the filter and leave it to dry fully before reusing.
[21]
5.
Once the filter is fully dry, reassemble the filter pack (protective mesh and filter) and
refit to cleaner.
I
mPORTANT:
Do not use the product without the pre-motor filter pack fitted.
ImPORTANT:
Always ensure the filter packs are fully dry before use.
To access the exhaust filter:
1. Unclip the exhaust grid from the rear of the cleaner.
[19]
2.
Separate the filter from the grid and wash the filter under warm water.
[20]
Do not use
hot water or detergents.
3.
Remove excess water from the filter and leave to dry fully before reusing.
[21]
4.
Remount the filter into the grid and refit it to the cleaner.
REmEmbER:
Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a Genuine Hoover consumable. Do not try and use the product
without a filter fitted.
Removing a blockage
1. Check if the dust container is full. If so refer to ‘Emptying the Dust Container’.
2. If the dust container is empty but suction is still low:
A.
Do the filters need cleaning? If so refer to ‘Cleaning the
Washable Filters’.
B.
Check if there is any other blockage in the system - Use a rod or pole to remove
any blockage from the extension tube or flexible hose.
C.
Check if pre-motor filter is fitted and filter door is closed
warning (Certain models only*)
- If the cleaner is used for a significant period of time
with a blockage, a thermal cut out will switch the cleaner off to prevent overheating.
The bag check indicator turn green once the cleaner has switched off to signal that the
thermal cut out has been activated. If this should happen, switch the cleaner off, unplug
and correct the fault. It will take about 45 minutes for the cut out to automatically reset.
*Certain models Only
** Certain models only, nozzles may vary according to model
