manualshive.com logo in svg

Honeywell R4140G, Руководство по установке, Страница: 3 / 32

Поделиться
Скачать
Honeywell R4140G Скачать руководство пользователя страница 3

R4140G, L AND M FLAME SAFEGUARD PROGRAMMING CONTROLS

60-0770—2

3

Plug-In Flame Signal Amplifiers

Applicable Flame Detectors

Type

Color  

Self-

Checking

Model

Flame Failure

Response Time

Fuel

Type

Models

Rectification   Green

No

R7247A

2 to 4 second

Gas

Rectifying
Flame Rods

Holders

a

 C7004. C7007,

C7011. Complete
Assemblies: C7005,
C7008, C7009, Q179.

R7247A,
R7247B

b

Oil

Rectifying
Photocells

c

C7003, C7010, C7013,
C7014.

Gas, Oil,
Coal

Ultraviolet
(Purple Peeper

C7012A or C.

Dynamic
Self-Check

R7247B

b

Gas

Rectifying
Flame Rods

Holders

a

: C7004, C7007,

C7011. Complete
Assemblies: C7005,
C7008, C7009, Q179.

R7247C

d

Gas, Oil,
Coal

Ultraviolet
(Purple Peeper

C7012E or F.

Infrared

Red

No

R7248A

2 to 4 second

Gas, Oil,   Infrared (Lead  

C7015.

Dynamic
Ampli-
Check®

R7248B

b

Coal

Sulfide)

Ultraviolet

Purple

No

R7249A

2 to 4 second

Gas, Oil

Ultraviolet
(Minipeeper)

C7027, C7035, C7044.

Blue

Dynamic
Self-Check

R7476A

d

Gas, Oil,
Coal

Ultraviolet
(Adjustable
Sensitivity)

C7076.

25,000V rms in a salt bath for one minute without
breakdown. It is rated at 200

°

F (93

°

C) for continuous

duty, and up to 350

°

F (177

°

C) for intermittent use.

���

Refer to the appropriate wiring diagram in the
Specifications for the R4140G,L or M. Follow the burner
manufacturer’s wiring diagram, if provided.

���

Make sure the loads do not exceed the terminal ratings.
Refer to the label on the R4140 or to the Terminal
Ratings in the Specifications section of the
Specifications for the R41406,L or M.

���

Check the power supply circuit. The voltage and
frequency must match those of the R4140. Do not
connect the R4140 to a circuit that is subjected to line
voltage variations, such as would occur with on-off
switching of heavy loads. A separate power supply
circuit can be required for the flame safeguard control.
Add required disconnect means and overload
protection.

���

Check all wiring circuits and complete the Static
Checkout in Table 2 before installing the R4140.

Installing the Flame Detector

NOTE:

Table 1 lists the flame detection systems available
for use with R4140 Programmers. Make sure you
are using the correct combination of amplifier and
flame detector(s).

Proper flame detector installation is the basis of a safe and
reliable flame safeguard installation. Refer to the instructions
packed with the flame detector and the burner manufacturer’s
instructions. Follow the instructions carefully for the best
possible flame detector application.

Keep the flame signal lead wires as short as possible from
the flame detector to the wiring subbase. Capacitance
increases with Ieadwire length, reducing the signal strength.
The maximum permissible leadwire length depends on the
type of flame detector, leadwire, and conduit. The ultimate
limiting factor in flame signal leadwire length is the signal
current. Refer to Table 4 in the Checkout section.

Table 1. Flame Detection Systems.

a

Order flame rod separately; see Instructions for the holder.

b

Circuitry tests the flame signal amplifier at least 150 times a minute during burner operation and shuts down the burner if the
amplifier fails.

c

Use only Honeywell part no. 38316 Photocell.

d

Circuitry tests all electronic components in the flame detection system (amplifier and detector) 60 to 240 times a minute during
burner operation and shuts down the burner if the detection system fails.

Содержание R4140G

































Отзывы:

Нет отзывов