Honeywell R4140G Скачать руководство пользователя страница 10

Страница: 10 / 32

R4140G, L AND M FLAME SAFEGUARD PROGRAMMING CONTROLS

60-0770—2

1ST STAGE
FUEL VALVE

2ND STAGE
FUEL VALVE
(OPTIONAL)

10 SECOND
INTERRUPTED
PILOT/IGNITION

5 SECOND IGNITION
(EARLY SPARK
TERMINATION)

FOR DIRECT SPARK IGNITION (OIL OR GAS)

ON MODELS WITH INTERRUPTED

PILOT/IGNITION ON TERMINAL 6

FOR DIRECT SPARK IGNITION (OIL OR GAS)

ON MODELS WITH INTERMITTENT

PILOT/IGNITION ON TERMINAL 6

REPLACING AN R4140M OR G WITH AN R4140L

WHITE

BLUE

YELLOW

MASTER
SWITCH

120V, 60 HZ
POWER
SUPPLY

L1 (HOT)

BLACK

WHITE

BLACK

IGNITION
TRANSFORMER

MAIN FUEL
VALVE(S)

BURNER
CONTROLLER

DAMPER
CONTROL

PREIGNITION
INTERLOCKS

WIRING SUBBASE
TERMINAL STRIP (4)

JUMPER

LOCKOUT
INTERLOCKS
(INCL. AIRFLOW
SWITCH)

PILOT/IGNITION

120V ALARM

HIGH FIRE

COMMON

MODULATE

SERIES 90
CONTROLLER

SERIES 90
FIRING RATE
MOTOR

LOW FIRE

MAIN FUEL
VALVES(S)

C7027A, C7035A, OR
C7044A ULTRAVIOLET
FLAME DETECTOR

RECTIFYING FLAME
ROD, RECTIFYING
PHOTOCELL, OR INFRA-
RED (LEAD SULFIDE)
FLAME DETECTOR

LOW FIRE
SWITCH

HIGH FIRE
SWITCH

LIMITS

C8349

BURNER MOTOR
(BLOWER)

ALTERNATE
LOW FIRE
SWITCH

C7012A,C,E,F OR
C7076A ULTRAVIOLET
FLAME DETECTOR

LEAVE INTERLOCKS CONNECTED BETWEEN TERMINALS 3 AND 16.

LEAVE INTERLOCKS CONNECTED BETWEEN TERMINALS 4 AND 16.
IF THERE IS A JUMPER WIRE BETWEEN TERMINALS 14 AND 16, REMOVE
IT AND INSTALL INTERLOCKS.

IF REPLACING MODEL WITH "START" INTERLOCKS, DISCONNECT THE
BURNER CONTROLLER FROM TERMINAL 16 AND CONNECT IT TO
TERMINAL 4.

IF REPLACING AN R4140M WITH OPEN DAMPER CONTACTS, REMOVE
DAMPER CONTROL FROM TERMINALS 10 AND L2, AND REMOVE
JUMPER WIRE FROM TERMINALS 11 AND 12.

IF REPLACING AN R4140M, ADD SERIES 90 CONTROLLER AND SERIES 90
FIRING RATE MOTOR.

5 SECOND IGNITION IS NOT AVAILABLE ON SOME MODELS.

REFER TO SPECIFICATIONS OF THE SPECIFIC R4140L MODEL TO
DETERMINE THE PILOT/IGNITION TIMING AVAILABLE ON TERMINAL 6.

FOR DIRECT SPARK IGNITION (OIL OR GAS), CONNECT THE
IGNITION TRANSFORMER AND FUEL VALVE(S) AS SHOWN IN THE
APPROPRIATE INSET.

ADD LOW FIRE SWITCH (IF NOT ALREADY CONNECTED).

ADD HIGH FIRE SWITCH.

Fig. 8. Sample block diagram of field wiring for replacing an R4140M or G with an R4140L.

Содержание R4140G

































Результаты поиска

Содержание R4140G

Отзывы:

Honeywell R4140G, Руководство по установке, Страница: 10 / 32

Результаты поиска

Содержание R4140G

Отзывы: