Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 68

Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 51

LDM Series Instruction Manual —

P/N 15885:H3 8/12/2019

51

Configuration for the LDM-32 and AFP-100

AFP-100 (UL 8th)

D.5 Configuration for the LDM-32 and AFP-100

LDM-32 DIP Switch (SW3) settings (for AFP-100):

1.

Relay Control:

Future Use - this switch must be set OFF on the AFP-100.

None

One

Two

Three

2.

Number of LDM-E32 Expanders Installed:

OFF

ON

OFF

ON

3.

Number of LDM-E32 Expanders Installed:

OFF

OFF

ON

ON

4.

8-Point Shift:

Set switch ON to shift MS-9200 LED function annunciation from the first eight annunciator positions on the

LDM-32F to the third LDM-E32F expander positions 57 - 64. This shift can only be set on an LDM-32F set for address 1 (system
using less than 56 software zones).

5.

Receive Only:

Set this switch ON for each LDM series that will provide the same information as another LDM series in a different

physical location (when two or more sets of LDM series have the same address, all but one must be configured as Receive Only.)

6.

Piezo Disable:

Set this switch ON to disable the piezo from sounding for any event.

7.

Switch Inhibit: T

o disable the point I/O control switches on the LDMs from functioning, set this switch ON. When inhibited, the

local Lamp Test switch continues to function. In addition, the

Acknowledge/Lamp Test

switch will function only in a local

capacity, unrecognized by the host AFP-100.

8.

Flash Inhibit:

Set this switch ON to disable the flashing of LEDs associated with unacknowledged events. F

lash Inhibit also

disables the piezo from sounding.

*The lamp driver must be set for addresses 1, 2, 3 or 4 when used with the AFP-100. Use address 1 for 56 zones. Use addresses 1, 2, 3
and 4 for 198 points. (Do not omit any address when annunciating 198 points or the AFP-100 will indicate a constant trouble). Refer to
Document 51010 for details.

12

3

45

6

78

8

8

LDM-32

Switch set to

ON

position

Switch set to

OFF

position

Lamp Driver Address

Set in the range 01-04

Ones

Tens

DIP Switch SW3

(see settings below)

Lamp Driver Mode

SW4

SW4

ALARM/TROUBLE

mode

(SW4 set to right side)

ALARM ONLY

mode

(SW4 set to left side)

«
...
49
50
51
52
53
...
»

Содержание NOTIFIER LDM Series





































































Отзывы:

Нет отзывов