Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 47

Страница: 47 / 68

LDM Series Instruction Manual —

P/N 15885:H3 8/12/2019

Configuration for the LDM-32 and NFS-3030/NFS2-3030, NCA/NCA-2, or AM2020/AFP1010

NFS2-3030 and NCA-2 (UL 9th),

C.9 Configuration for the LDM-32 and NFS-3030/NFS2-3030, NCA/NCA-2, or

AM2020/AFP1010

LDM-32 DIP Switch (SW3) settings
(for NFS-3030/NFS2-3030, NCA/NCA-2, or AM2020/AFP1010):

Relay Control

: Set to ON when the lamp driver is used to control relays or to provide fan shutdown (see the Annunciator Control

System manual, Document 15842 for more details).

None

One

Two

Three

Number of LDM-E32 Expanders Installed

OFF

Number of LDM-E32 Expanders Installed

OFF

8-Point Shift

: This switch must always be set OFF on the NFS-3030/NFS2-3030, NCA/NCA-2, or AM2020/AFP1010.

Receive Only

: Set this switch ON for each LDM series that will provide the same information as another LDM series in a different

physical location (when two or more sets of LDM series have the same address, all but one must be configured as Receive Only.)

Piezo Disable

: Set this switch ON to disable the piezo from sounding for any event.

Switch Inhibit:

Set this switch OFF to enable any control switches wired to the Lamp Driver. If set ON, switches wired to the

Lamp Driver will not execute their intended functions, but will serve only as a local Lamp Test for their respective points.

Flash Inhibit

: Set this switch ON to disable the flashing of LEDs associated with unacknowledged events. F

lash Inhibit also

disables the piezo from sounding. Flash Inhibit must be ON when using the relay expander module (LDM-R32).

C.10 Wiring the LDM for the NFS-3030/NFS2-3030, NCA/NCA-2, or AM2020/AFP1010

The LDM-32 and one expander can be configured for up to 64 alarm points by setting Switch SW4 to the 'ALARM ONLY' position.

Figure C.2 Lamp Driver Alarm Points

LDM-32

Switch set to

position

Switch set to

OFF

position

Lamp Driver Address

Set in the range 01-32

Ones

Tens

DIP Switch SW3

(see settings below)

SW4

ALARM/TROUBLE

mode

(SW4 set to right side)

ALARM ONLY

mode

(SW4 set to left side)

OUTPUTS

SW4

Points

P(1) - P(8)

LDM-32 Lamp Driver

Points

P(9) - P(16)

Points

P(17) - P(24)

Points

P(25) - P(32)

OUTPUTS

Points

P(33) - P(40)

Points

P(41) - P(48)

Points

P(49) - P(56)

Points

P(57) - P(64)

LDM-E32 Expander

Содержание NOTIFIER LDM Series





































































Результаты поиска

Содержание NOTIFIER LDM Series

Отзывы:

Honeywell NOTIFIER LDM Series, Инструкция по эксплуатации, Страница: 47 / 68

Результаты поиска

Содержание NOTIFIER LDM Series

Отзывы: