manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Инструкция по эксплуатации, Страница: 43 / 68

Поделиться
Скачать
Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 43

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

43

AIM-200 Point Annunciation

System 5000 (UL 8th)

Figure B.11 illustrates the configuration of the LDM-R32 Relay Expander to activate alarms and troubles for up to 56 zones with the last 
eight relays dedicated to the CPU functions listed below.

TB1

1
2

3
4

5
6

7
8

4

3

2

1

5
6

7
8

1
2
3
4

5
6

7
8

1
2
3
4
5
6
7

8

TB3

TB4

TB5

TB2

TB6

TB1

1
2
3
4
5
6
7

8

1
2
3
4
5
6
7

8

TB2

Address #1

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

System Status Indicators *

1   -   4

17   -   20
33   -   36
49   -   52

5   -   8

21   -   24
37   -   40
53   -   56

9    -   12

25   -   28
41   -   44

13  -   16

29   -   32
45   -   48

N.O. Contacts

N.O. Contacts

N.O. Contacts

N.O. 

Contacts

Trouble

Alarm

Alarm

Trouble

Trouble

Alarm

Alarm

Trouble

Common for TB1
Common for TB2

Common

for TB3

* System Functions

System Alarm
not used
not used
not used
System Trouble
Signals Silenced
not used
Supervisory

NAC Circuit #1 ON
NAC Circuit #2 ON
Municipal Tie ON
Alarm Relay ON
NAC Circuit #1 Trouble
NAC Circuit #2 Trouble
Municipal Tie Trouble
Alarm Relay Trouble

Common

for TB4

* It is assumed that the '8-Point Shift' will be selected only on systems containing less than 56 circuits.

Figure B.11  Alarm and Trouble Relays with 8-Point Shift

Содержание NOTIFIER LDM Series





































































Отзывы:

Нет отзывов