manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Инструкция по эксплуатации, Страница: 20 / 68

Поделиться
Скачать
Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 20

20

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

Wiring Considerations

Control Switch Wiring

4.10  Control Switch Wiring

Optional zone/point control switches must be momentary type. Wiring from the LDM to the control switches must be in conduit and in 
the same room as the LDM since the wires are not supervised. Use the cables supplied in the cable kits to wire the control switches.

1

Each LDM must be set for Alarm/Trouble Mode by positioning slide switch SW4 to the right, for the optional control switches to func-
tion (the Acknowledge/Lamp Test switch will work in either mode). In this configuration, each LDM-32 and LDM-E32 provides 16 
alarm drivers, 16 trouble drivers and 16 control switches. The alarm and trouble drivers are assigned to host FACP zones/points via user 
setup/installation. See tables in the appendix for the appropriate FACP for additional information. Not all switches must be used - 
switches can be wired only for desired functions. To determine the function of each switch and driver in a specific FACP application, 
refer to the Appendices in this manual and the appropriate FACP Installation Manual.

J11

+5

+24

Common

J6

J5

J4

SWITCH
MATRIX

LAMP
POWER

OUTPUTS

J7

J8

J10

J9

Note: All LEDs must be in the same room as the LDM modules.

Point Status LEDs:

Use red for alarm points, 

yellow for trouble points, and

green for output points

Use 10K W, 1/4 watt resistors for 

each point if using 2 mA LEDs.

Custom 
Graphic 
Display

System

Trouble LED

(Yellow)

Wiring is not 
supervised

Figure 4.9  Typical LDM-to-Graphics Display Connection @ 24 VDC

1. Switches must be UL listed to switch 5 volts DC @ 0.5mA. Switches must be key-lock type, secured in a locked enclosure 

or a security key switch must be installed to control access. All switches must be installed in the same room as, and no more 
than 20 feet from, the LDM enclosure. Switch wiring must be in conduit.

Acknowledge/ Lamp Test 

Switch (momentary)

Switch #16

Switch #15

Switch #14

Switch #13

Switch #12

Switch #11

Switch #10

Switch #9

Switch #8

Switch #7

Switch #6

Switch #5

Switch #4

Switch #3

Switch #2

Switch #1

Figure 4.10  Optional Zone/Point-Control Switch Wiring

Содержание NOTIFIER LDM Series





































































Отзывы:

Нет отзывов