Honeywell CIPer 50 Скачать руководство пользователя страница 46

Страница: 46 / 85

CIPer

MODEL 50 CONTROLLER

–

INSTALLATION AND COMMISSIONING INSTRUCTIONS

31-00233-02

Panel Bus Connection

The CIPer Model 50 controller features two RS485 interfaces to which Panel Bus modules can be connected:
RS485-1 (consisting of push-in terminals 24 [GND-1], 25, and 26) and/or RS485-2 (consisting of push-in
terminals 29, 30, and 31 [GND-2]).

NOTE

GND-2 is internally connected with 24V-0 (terminal 1)

Overview of Panel Bus I/O Modules

Figure 34: Overview of Panel Bus I/O Modules

Panel Bus Considerations

•

RS485-1 (isolated)

–

Max. Panel Bus length:

1200 feet. Any type of cabling and topology (including star and loop topology) possible. No

additional end termination permitted.

3600 feet (9.6

–

78.8 kbps) or 2400 feet (115.2 kbps) (see also section "RS485 Standard").

Mandatory twisted-pair or telephone cable and daisy chain topology. The CIPer Model 50

must be positioned at one end of the Panel Bus, and an end termination (120

Ω

) at the other

end. Further, the three-position slide switch (see Figure 14) must be set to "END."

•

RS485-2 (non-isolated)

–

Max. Panel Bus length:

1200 feet. Any type of cabling and topology (including star and loop topology) possible. No

additional end termination permitted.

3600 feet (9.6

–

78.8 kbps) or 2400 feet (115.2 kbps) (see also section "RS485 Standard").

Mandatory twisted-pair or telephone cable and daisy chain topology. The CIPer Model 50

controller must be positioned at one end of the Panel Bus, and an end termination (120

Ω

) at

the other end.

–

Must not extend beyond a single building or building floor

•

Max. no. of Panel Bus I/O modules per RS485 interface

–

Max. no. of Panel Bus I/O modules of a given model: 16

–

Total max. no. of Panel Bus I/O modules: 64

•

Max. no. of Panel Bus I/O modules per CIPer Model 50

–

Max. no. of Panel Bus I/O modules of a given model: 32

Содержание CIPer 50





















































































Результаты поиска

Содержание CIPer 50

Отзывы:

Похожие инструкции для CIPer 50

Бренды по названию

Популярные бренды

Honeywell CIPer 50, Инструкции по установке и пусконаладке

Результаты поиска

Содержание CIPer 50

Отзывы:

Похожие инструкции для CIPer 50

Бренды по названию

Популярные бренды