Honeywell CIPer 50 Скачать руководство пользователя страница 7

Страница: 7 / 85

CIPer

MODEL 50 CONTROLLER

–

INSTALLATION AND COMMISSIONING INSTRUCTIONS

31-00233-02

WEEE DIRECTIVE

WEEE: Waste Electrical and Electronic Equipment Directive

•

At the end of the product life, dispose of the packaging and product in an appropriate

recycling center.

•

Do not dispose of the device with the usual domestic refuse.

•

Do not burn the device.

Standards and Approvals

Degree of Protection:

IP20 (mounted on walls, with two accessory MVC-80-AC1 covers)
IP30 (mounted in cabinet doors, with accessory MVC-80-AC2)

Device meets EN 60730-1, EN 60730-2-9, UL60730, and UL916.

Refer to Code of Practice standards IEC 61000-5-1 and -2 for guidance.

The device complies with Ethernet Protocol versions IEEEC 802.3.

The device supports BACnet IP and BACnet MS/TP communications as per ANSI / ASHRAE 135-2012

Specifications of Controller

Table 2. CIPer Model 50 specifications

Power supply

19 … 29

VAC, 50/60 Hz or

20 … 30

VDC

Power consumption

DC: 7 W (max 9 W)
AC: 10 VA (max 12 VA)

Heat dissipation

Max. 9 W at DC power supply
Max. 9 W at AC power supply

Current consumption

DC: 300 mA (max. 375 mA)
AC: 400 mA (max. 500 mA)

Ambient temperature

32 … 104 °F

…

40 °C) (wall-mounting)

32 … 122 °F

…5

0 °C) (cabinet/door mounting)

Storage temperature

4 …

+158 °F (-20

…+

70 °C)

Humidity

5 … 95% rh.

non-condensing

Dimensions

See

Figure 21

and

Figure 22

Degree of protection

IP20 (mounted on walls, with two accessory MVC-80-AC1 covers)
IP30 (mounted in cabinet doors, with accessory MVC-80-AC2)

Fire class

Weight

1.33 lb (0.6kg) excl. packaging

Содержание CIPer 50





















































































Результаты поиска

Содержание CIPer 50

Отзывы:

Похожие инструкции для CIPer 50

Бренды по названию

Популярные бренды

Honeywell CIPer 50, Инструкции по установке и пусконаладке

Результаты поиска

Содержание CIPer 50

Отзывы:

Похожие инструкции для CIPer 50

Бренды по названию

Популярные бренды