Honeywell Chadwick-Helmuth 8500C Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 186

background image

Repair

8500C/8500C+ System Maintenance Manual

5-49

c.

Remove both EPROM’s as follows: using a small, straight-blade screwdriver, carefully
pry up one end of EPROM just a little bit. Pry up other end a little. Go back and forth until
EPROM is loose.

Trying to pry out the EPROM in one step will bend the EPROM pins.

d.

Remove new EPROM’s from container. They should have a higher dash number or letter
than ones removed.

Precautions against electrostatic discharge are critical at this stage.

e.

Install new EPROM’s as follows: orient EPROM with notched end in direction shown in
Figure 5-15. Align left end of EPROM with left end of SRAM memory IC (U10) and
make sure pins are all straight and part-way into each socket hole when EPROM is set on
socket - look along the board, beneath the EPROM for pins bent under. Once pins all align
properly, push EPROM slowly but firmly into socket, keeping it straight.

NOTE: If pins do not align well, very carefully push EPROM against a flat surface to form
pins inward until they are parallel.

f.

Install bezel (Figure 5-17 (4)) on keypad panel (1) and secure with ten screws (32) and

four screws (33).

5.7.4 Battery Pack Check and Replacement

5.7.4.1

Battery Pack Check

a.

Power the 8500C/C+ unit continuously for 72 hours. This ensures the battery pack has

become fully charged.

b.

To access battery pack, remove ten screws (Figure 5-17, (32)) and four screws (33) and

remove bezel (4).

c.

Fold back printer/disk drive assembly so that it stands straight up on its side with keypad

panel (1) lying flat on table, as shown in Figure 5-16.

d.

Check battery voltage for 3.6 V. Replace battery pack, if necessary, in accordance with the

next section.

e.

Install bezel (Figure 5-17 (4)) on keyboard panel (1) and secure with ten screws (32) and

four screws (33).

5.7.4.2

Battery Pack Replacement (Figure 5-17)

The battery pack is located on analog board A2. Replace battery pack as follows:

a.

To access analog board A2, remove digital board A1 in accordance with instructions in
Section 5.8.1.1.1.

CAUTION

CAUTION

«
...
91
92
93
94
95
...
»

Содержание Chadwick-Helmuth 8500C



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chadwick-Helmuth 8500C

Бренд: dbx Страницы: 2

Бренд: J.P. Instruments Страницы: 9

Бренд: J.ASSY Страницы: 13

Бренд: Parkside Страницы: 114

Бренд: Yamaha Страницы: 48

Бренд: Hach Страницы: 96

Бренд: DAKOTA ULTRASONICS Страницы: 50

Бренд: Jamar Страницы: 4

Бренд: Teledyne Страницы: 85

Бренд: FM Marin Страницы: 8

Thermo Scientific iCE 3000 Series

Бренд: ThermoFisher Scientific Страницы: 42

Бренд: PCE Health and Fitness Страницы: 66

Бренд: SAND Страницы: 15

Бренд: SNV Engineering Страницы: 43

Бренд: Skil Страницы: 80

PROline promag 23

Бренд: Endress+Hauser Страницы: 108

Бренд: FORK Страницы: 4

Бренд: A&D Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды