Honeywell Chadwick-Helmuth 8500C Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 186

background image

Calibration Tests

8500C/8500C+ System Maintenance Manual

5-15

k.

Press

CHANGE

soft key to select

<DEGREES>

.

l.

Press

ENTER

soft key.

m.

Monitor signal generator output with spectrum analyzer with marker at 100 Hz. Adjust
signal generator output channel connected to Velocimeter input until amplitude is 13.44 +/
- 0.05 mV RMS.

n.

Wait 10 seconds for 8500C/C+ gain to settle.

o.

Press

START

key on 8500C/C+.

p.

Verify that display indicates:

FREQUENCY: 100.0 +/- 0.1 Hz

VIB LEVEL: 1.000 +/- 0.04 IPS

PHASE ANGLE: 180° deg. +/- 3°

q.

Press

STOP

key.

5.5.1.4

Noise and Spurious Signals Test

This test measures the level of noise and spurious signals generated in the 8500C/C+.

a.

Disconnect Velocimeter and magnetic pickup coax cables from cable 8998.

b.

Press

SPECTRUM

key on 8500C/C+.

c.

Press

SETUP

key.

d.

Key in

1000 (Hz)

with numeric keys in

MAXIMUM FREQUENCY

field.

e.

Select

SEEK

: field with arrow keys.

f.

Press

CHANGE

soft key to select

SEEK:<OFF>

.

g.

Press

ENTER

soft key and wait 10 seconds.

h.

Press

START

key.

i.

Verify that no noise signal is present on display above 0.005 IPS.

NOTE: At minimum display scale, each dot on display = .001 IPS.

NOTE: If any noise signals appear, you can use left-right arrows to move cursor to noise
peak. IPS level and frequency of peak will read out at top of display.

5.5.1.5

Anti-Alias Filter Response

This test measures the ability of the two anti-alias filters to reject frequencies caused by aliasing. This
test uses a signal generator to inject a signal known to cause an alias frequency into the 8500C/C+. The
8500C/C+ then measures the alias frequency to determine how well the alias frequency was rejected.

5.5.1.5.1 500 Hz Anti-Aliasing

a.

Set up spectrum analyzer to view a 13.44 mV RMS, 1722-Hz signal. Use the following

analyzer settings:

Frequency:

Baseband, Start: 0 Hz, Stop: 2000 Hz

Trigger:

Free run

Average:

Off

«
...
57
58
59
60
61
...
»

Содержание Chadwick-Helmuth 8500C



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chadwick-Helmuth 8500C

Бренд: Kanomax Страницы: 2

Бренд: Keithley Страницы: 156

Бренд: F.W. Bell Страницы: 75

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Badger Meter Страницы: 56

ModMAG M Series

Бренд: Badger Meter Страницы: 4

NUFLO Scanner 2000 microEFM

Бренд: Cameron Страницы: 8

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: Oakton Страницы: 69

Бренд: Yamaha Страницы: 14

Disklavier Mark II XG Series

Бренд: Yamaha Страницы: 12

Бренд: YATO Страницы: 36

Бренд: TSI Instruments Страницы: 4

Бренд: U.S. Solid Страницы: 30

OMCL-AC240TS-R3

Бренд: Olympus Страницы: 3

Бренд: SATO KEIRYOKI Страницы: 2

Бренд: Lutron Electronics Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды