manualshive.com logo in svg

Honeywell Chadwick-Helmuth 8500C, Руководство по обслуживанию

"Руководство по техническому обслуживанию Honeywell Chadwick-Helmuth 8500C - это бесплатный мануал, который можно скачать с manualshive.com. Здесь вы найдете все необходимые инструкции по уходу и обслуживанию вашего прибора, чтобы он всегда работал на высоком уровне."

Поделиться
Скачать
background image

Detailed Description

8500C/8500C+ System Maintenance Manual

4-9

b.

Display Heater. The fi27 VDC power from the power supply filter is regulated at 
+12 VDC and applied to the heater controller module. This module samples the resistance 
of the heater every 10 seconds. If the resistance falls below approximately 83 ohms, 
indicating that the screen temperature is below approximately 7°C, then the controller 
begins heating the display. As the heater temperature rises, the heater resistance increases. 
Once the resistance rises above approximately 83 ohms, the screen is at operating 
temperature and the heater is turned off. The heater is capable of keeping the LCD screen 
at +7°C with ambient temperatures down to -40°C.

c.

EL Controller. The fi27 VDC power from the power supply is applied to a variable 
voltage regulator. The voltage regulator output (+1.5 to +13 VDC) is changed by an 
external BRIGHTNESS ADJ potentiometer on the control panel in the disk drive 
compartment. This regulated voltage drives an 800 Hz, 100 Vrms inverter, which powers 
the EL lamps behind the LCD and keypanel. The brightness of the lamps is proportional to 
the inverter AC voltage. The inverter AC voltage output is proportional to the DC voltage 
input to the inverter.

4.2.1.2

Printer/Disk Drive Assembly

The printer/disk drive assembly contains three printed circuit boards: a printer board, a distribution 
board, and a power supply board; a printer assembly; and a disk drive assembly. The printer board 
drives the printer. The distribution board provides an interface between the balancer/analyzer assembly 
and printer/disk drive assembly. The power supply board generates the DC operating voltages for the 
balancer/analyzer assembly and printer/disk drive assembly. The printer assembly prints the data. The 
disk drive assembly reads the data from the diskette.

4.2.1.2.1 Printer Board

The printer board receives data and control commands from the communications controller in the 
8500C/C+ digital board, and status signals are returned to the digital board. The data and control 
commands are converted from serial form to parallel form to drive the print head. Three amplifiers 
amplify the print drive signals to the proper levels needed to drive the print heads. The board also 
contains a paper feed switch to index paper through the paper feed slot. An LED paper sensor informs 
the processor when paper is in the unit.

4.2.1.2.2 Distribution Board

The distribution board provides cable interfacing between the balancer/analyzer assembly and printer/
disk drive assembly.

4.2.1.2.3 Power Supply Board (Figure 4-5)

The power supply board converts the 28 VDC input power from the aircraft to the DC voltages needed 
to operate the circuit boards in the balancer/analyzer assembly and printer/disk drive assembly. The 
input power from the aircraft can be 12 to 28 VDC of either polarity. The input power is applied to a 
diode bridge to set the input voltage to the correct polarity. The output of the bridge is applied across a 
FET switch and transformer. The transformer outputs are rectified and filtered to produce two +5 
VDC, one +12 VDC, and one -12 VDC output voltage. The power supply contains a closed-loop 
regulator, which keeps the output voltages constant for varying input voltage and load. An optoisolator 
feeds back the output voltage across the isolation barrier. A light emitting diode (LED) indicates when 
power is on.

Содержание Chadwick-Helmuth 8500C



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chadwick-Helmuth 8500C

Eaton Power Xpert PXM 4000 Quick Start Manual preview
Power Xpert PXM 4000
Бренд: Eaton Страницы: 28
Oldham MX15 Installation And Operating Instructions Manual preview
MX15
Бренд: Oldham Страницы: 22
HANYOUNGNUX HP3 Instruction Manual preview
HP3
Бренд: HANYOUNGNUX Страницы: 4
QALCOMET HEAT 1 User Manual preview
HEAT 1
Бренд: QALCOMET Страницы: 52
Danfoss LLG Installation Manual preview
LLG
Бренд: Danfoss Страницы: 4
LOVATO ELECTRIC DMED302 Instruction Manual preview
DMED302
Бренд: LOVATO ELECTRIC Страницы: 10
e-sylife Gas Module Installation Manual preview
Gas Module
Бренд: e-sylife Страницы: 2
Keysight M8290A Getting Started Manual preview
M8290A
Бренд: Keysight Страницы: 56
Omega DPG1001AD Instruction Sheet preview
DPG1001AD
Бренд: Omega Страницы: 4
Keysight M9703A Series Startup Manual preview
M9703A Series
Бренд: Keysight Страницы: 26
R&S ZNB Series User Manual preview
ZNB Series
Бренд: R&S Страницы: 1611
PCB Piezotronics HT356A43 Installation And Operating Manual preview
HT356A43
Бренд: PCB Piezotronics Страницы: 17
Edu-Logger 900-208 Manual preview
900-208
Бренд: Edu-Logger Страницы: 12
bihl+Wiedemann BWU2427 Installation Instructions Manual preview
BWU2427
Бренд: bihl+Wiedemann Страницы: 16
A&D AD-8951 Instruction Manual preview
AD-8951
Бренд: A&D Страницы: 8
Fluke Biomedical Victoreen 07-494 Operator'S Manual preview
Victoreen 07-494
Бренд: Fluke Biomedical Страницы: 34
JPT Seal-355-3 User Manual preview
Seal-355-3
Бренд: JPT Страницы: 19
QuantoLux QLX3 Installation Manual preview
QLX3
Бренд: QuantoLux Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды