manualshive.com logo in svg

Honeywell Aquastat L4006, Руководство по установке, Страница: 7 / 20

Поделиться
Скачать
Honeywell Aquastat L4006 Скачать руководство пользователя страница 7

Aquastat L4006,7,8;L6006,7,8

 

5 60-2104—01

Fig. 3 Approximate installation dimensions in inches 

(mm) for surface mount models.

Fig. 4 Approximate immersion well dimensions in inches 

(mm) for all models except L4006C and L6006B.

Fig. 5 Approximate boiler fitting and bulb dimensions in 

inches (mm) for L4006C and L6006B.

1/2 — 14 IN. NPT

7/16
(11)

3  (76)

1-1/2  (38)

M8789B

1/2 OR 3/4 — 14 IN. NPT

3/8

(10)

3  (76)

1-5/16  (33)

M8799B

Dimensions:

Installation: (See Figures 1, 2, and 3).
Immersion Well: (See Fig. 4).
Boiler Fitting and Bulb: (See Fig. 5).

DIMENSIONS

Fig. 1 Approximate case installation dimensionsin 

inches (mm) for direct insertion models.

Fig. 2 Approximate installation dimensions in inches 

(mm) for remote bulb models. Otherdimensions are the 

same as Fig. 1.

M8957A 

KNOCKOUT FOR 3/4  (19 ) 
CONDUIT ON ALL MODELS. SIMILAR 
KNOCKOUT ON BOTTOM FOR  
HORIZONTAL INSERTION AND  
REMOTE BULB MODELS. 

1 (25) 

5/16 

(8) 

2 (51) 

2-1/8 (54) 

5-5/8 
(136) 

1-7/8 

(48) 

3/16 

(5) 

RESET  

BUTTON 

(L4006E, 

L4008E 

ONLY) 

KNOCKOUT FOR 3/4 (19)  
CONDUIT ON VERTICAL  
INSERTION MODELS ONLY  

ELEMENT FOR HORIZONTAL IMMERSION 

3/4 
(19) 

ELEMENT  
FOR VERTICAL  
IMMERSION 

11/16 

(18) 

3/4 

(19) 

SENSING 
ELEMENT 
CAPILLARY 

3/8 (10) 

1-1/4 

(32) 

ALTERNATE POSITION 
OF SENSING ELEMENT 
CAPILLARY 

13/64 
  (5)  (3) 

MOUNTING 
HOLE FOR 
3/16 IN. (5 MM) 
SCREW (3) 

15/16 

(24) 

4-3/16 

(106) 

ALTERNATE POSITION 
OF SENSING ELEMENT 
CAPILLARY 

M8823 

M8958B

7/8 IN. (22 MM) 
STANDARD
KNOCKOUT (2)

1

(25)

2 (51)

5-5/8
(136)

2-3/4 (70)

2 (51)

CL

Содержание Aquastat L4006





















Отзывы:

Нет отзывов