manualshive.com logo in svg

Honeywell Aquastat L4006, Руководство по установке, Страница: 5 / 20

Поделиться
Скачать
Honeywell Aquastat L4006 Скачать руководство пользователя страница 5

Aquastat L4006,7,8;L6006,7,8

 

3 60-2104—01

Table 1. L4006, L4007, L4008 Controller (SPST Switching) Specifications

Model Application Range °F (°C)

Midscale 

Differential °F 

(°C)

Insertion

Switching On 

Temperature 

Rise

Available Options

L4007A High or low 

limit

100° F to 240° F

(38° C to 116° C)

2° F or 5° F

(1° C or 3° C)

fixed,

5° F to 30° F

(3° C to 17° C)

adjustable

Horizontal 

or

vertical

Breaks

-Insulation depth 

1-1/2 in. or 3 in. (38 

mm or 76 mm).

L4007B Circulator

100° F to 240° F

(38° C to 116° C)

5° F (3° C) fixed

or

5° F to 30° F

(3° C to 17° C)

adjustable

Vertical

Makes

-Celsius scale mark-

ings.

L4008A High or 

low limit 

Circulator

100° F to 240° F

(38° C to 116° C)

or

130° F to 270° F

(54° C to 132° C)

5° F (3° C) fixed,

5° F to 30° F

(3° C to 17° C)

adjustable

Remote 

bulb

direct

immersion

Breaks

-Remote capillary 

5-1/2 ft (1.7 m), 

8-1/2 ft (2.6 m) or 10 

ft (3.0 m).

-Factory-set scale 

stops at 120°, 170°, 

or 200° F (49°, 77°, 

or 93° C)

-Celsius scale 

markings.

-Front cover screw.

L4008B Circulator

100° F to 240° F

(38° C to 116° C)

5° F (3° C) fixed

or

5° F to 30° F

(3° C to 17° C)

adjustable

Remote 

bulb

direct

immersion

Makes

-Capillary 5-1/2 ft 

(1.7 m).

L4008Eb High limit

40° F to 80° F

(4° C to 27° C) or

130° F to 270° F

(54° C to 132° C)

Manual reset

Remote 

bulb

Breaks

-Factory-set scale 

stops at 140°, 200°, 

or 250° F (60°, 93°, 

or 121° C).

-Capillary 5-1/2 ft or 

20 ft (1.7m or 6.1 

m).

a Some models include copper well or fitting; specify when ordering. Also specify boiler tapping size 1/2 or 3/4 in. (13 to 19 

mm) NPT and insulation depth.

b Manual reset (trip-free) switch breaks circuit and locks out when controlled medium reaches setpoint. Controlled tem-

perature must drop 20° F (11° C) below setpoint before contacts can be manually reset.

SPECIFICATIONS

Содержание Aquastat L4006





















Отзывы:

Нет отзывов