manualshive.com logo in svg

Honeywell Aquastat L4006, Руководство по установке, Страница: 19 / 20

Поделиться
Скачать
Honeywell Aquastat L4006 Скачать руководство пользователя страница 19

Aquastat L4006,7,8;L6006,7,8

 17 60-2104—01

MATERIAL SAFETY DATA SHEET

Section 1. Product And Company Identification
Product Name: Heat Conductive Compound
MSDS ID: DS9021
Synonyms: MS1699
Product Use: Heat conductive material used to enhance
contact and heat transfer in temperature sensor 
applications.

Ingredient

CAS Number

Percent

PEL

TVL

#2 Lithium Complex Grease (70%):

Mineral Oil

64742-65-0

35-50

5 mg/m³

5 mg/m³

Mineral Oil

64742-62-7

20-25

5 mg/m³

5 mg/m³

Lithium Hydrostearate/

Sebacate

Complex

68815-49-6

4-9

—

—

Zinc Alkyldithiophosphate

68649-42-3

0-2

—

—

Aluminum Paste (30%):
Aluminum, as Al

7429-90-5

20-25

15 mg/m³

10 mg/m³

Aliphatic Petroleum Distillates 8052-41-3

10-15

2900 mg/m³

525 mg/m³

Stearic Acid

57-11-4

1-2

—

Aromatic Petroleum Distillates 64742-95-6

1-2

5 mg/m³

5 mg/m³

a Additional Information: Part No. 120650 (0.5 oz tube); Part No. 107408 (4 oz can); Part No. 197007 (5 gallon container). 

May also contain minute amounts of lithium and molybdenum lubricant compounds..

Section 4. First Aid Measures
Eye Contact: Flush eyes with water for 15 minutes. Remove 
any contact lenses and continue to flush. Obtain medical 
attention if irritation develops and persists.
Skin Contact: Remove excess with cloth or paper. Wash 
thoroughly with mild soap and water. Obtain medical atten-
tion if irritation develops and persists.
Ingestion: Contact physician or local poison control center 
immediately.
Inhalation: Remove patient to fresh

Manufacturer: Honeywell Inc., 1985 Douglas Drive North,
Minneapolis, MN 55422.
Date Released: October 8, 1999
NFPA Ratings:
Health 0; Flammability 1; Reactivity 0; Personal Protection B
Section 2. Composition
Information on Ingredients

Section 3. Hazard Identification

Acute Health Effects:
Skin: Excessive contact may cause skin irritation and der-
matitis.
Eye: Direct contact with eye will cause irritation.
Inhalation: No adverse effects are expected.
Ingestion: Ingestion of product may cause nausea, vomiting 
and diarrhea.

Chronic Health Effects

:

Existing skin rash or dermatitis may be aggravated by
repeated contact.
OSHA Hazard Classifications: None.
Carcinogenicity: Not considered to be a carcinogen by
either OSHA, NTP, IARC, or ACGIH.

MATERIAL SAFETY DATA SHEET

WARNING

Explosion Hazard.
Can cause serious injury, death or property damage.
This product is intended for use only in systems with a 
pressure relief valve.

CHECKOUT

Check to make certain that the Aquastat Controller is prop-
erly installed and adjusted. Put the system into operation 
and observe the action of the controller through several 
cycles to make certain it provides proper control of the 
system as described in the OPERATION section. Make 
any additional adjustments necessary for assuring comfort 
requirements.

Содержание Aquastat L4006





















Отзывы:

Нет отзывов