29
Security Codes & Authority Levels
(Continued)
How to Assign Security Codes and User Attributes
The following lists the various command strings for adding security codes and attributes.
Refer to the User Setup chart at the back of this manual for factory defaults of user attributes
and to keep a record of user programming.
NOTE:
Partition Master codes (VISTA-20P Series only) apply only to those user numbers previously
assigned (by the system master/installer) to the partition master’s partition.
Add a User:
System/Partition Master code + [8] + user no. + new user’s security code
(
Users 03/33 are preset
User 01 = installer
User 03 = partition 1 master
to partition programmers,
User 02 = master
User 33 = partition 2 master
but can be changed.)
The Keypad beeps once to confirm that new user was added.
Delete a User:
System/Partition Master code + [8] + [user no.] + [#] [0]
The security code and all attributes* set for this user number, including any
associated RF keys, are erased from the system.
(*except assigned partition)
Authority Level:
System/Partition Master code + [8] + [user no.] + [#] [1]+ auth. level
Factory Defaults:
Authority Levels (see definitions on previous page):
users 04-32/34-49 = 0
0 = standard user
3 = duress
users 03/33 = 4
1 = arm only
4 = partition master (VISTA-20P Series only)
2 = guest
Access Group:
System/Partition Master Code + [8] + [user no.] + [#] [2]+ group (1-8)
Factory Defaults:: none
You can assign users to a group, then set an access schedule that defines the
times this group of users can operate the system. The system ignores these users
outside the scheduled times.
User’s Partition:
System Master Code + [8] + [user no.] + [#] [3] + [0] + partition(s) + [#]
(VISTA-20P only)
This command assigns the partitions the user can access. If more
Factory Defaults:
than one, enter partition numbers sequentially, then press [#] to end.
Part. 1 = users 03-32
E.g., master code + [8] + [user no.] + [#] [3] + [0] + [1] [2] + [#] gives
Part. 2 = users 33-49
the user access to partitions 1 and 2 and the common partition.
Partition Entries:
1 = partition 1 and common; 3 = common partition only
2 = partition 2 and common
RF Zone Number:
Master/Part. Prog. Code + [8] + [user no.] + [#] [4]+ zone no.
(adding a Key Fob)
Use this command to assign a wireless button (key fob) to a user for arming/
disarming functions (key fob must be enrolled in system first; see installer).
Factory Defaults:: none
Zone number: enter the zone number assigned to a button on the key fob that will
be used for arming/disarming by this user.
Deactivating a key fob:
You can deactivate the arming/disarming functions for a
key fob (ex. if lost or stolen) by deleting the associated key fob user. See “Delete
a User” above. Other key fob functions such as panic or device activation (if
programmed) remain active. To fully remove the programming for a key fob, see
your installer.
Pager On/Off:
Master/Part. Prog. Code + [8] + [user no.] + [#] [5] + 0 or 1
Factory Defaults:
You can program a user so that a message is sent to a pager
users 01-49 = 1 (on)
whenever this code is used to arm or disarm the system.
Paging On/Off: 1 = allow paging; 0 = no paging for this user
Содержание Ademco Vista Series
Страница 62: ...58 NOTES...
