Holzstar 5904150, Руководство по эксплуатации

Страница: 8 / 22

8 BTS-Series | Version 3.06
Scope of delivery and Accessories
General risks during internal transport
Devices may only be transported by authorized and qua-
lified persons. Act responsibly during transport and al-
ways consider the consequences. Refrain from daring
and risky actions.
Gradients and descents (e.g. driveways, ramps and the
like) are particularly dangerous. If such passages are
unavoidable, special caution is required.
Before starting the transport check the transport route for
possible danger points, unevenness and disturban-ces
as well as for sufficient strength and load capacity.
Danger points, unevenness and disturbance points must
be inspected before transport. The removal of danger
spots, disturbances and unevenness at the time of trans-
port by other employees leads to considerable dangers.
Careful planning of internal transport is therefore essen-
tial.
5.2 Packaging
All used packaging materials and packaging aids of the
grinding system are recyclable and generally need to be
transported to the material recycling.
Crush the packaging material made of cardboard and
supply it to the waste paper collection.
The films are made of polyethylene (PE) and the uphol-
stery parts are made of polystyrene (PS). These materi-
als have to be delivered to a recycling station of the re-
sponsible dumping company.
5.3 Storage
The belt and disc sander must be thoroughly cleaned be-
fore being stored in a dry, clean and frost-free environ-
ment. Cover the machine with a protective tarpaulin.
6 Scope of delivery and Acces-
sories
6.1 Scope of delivery
Check the machine immediately after delivery for trans-
port damage and shortages. To do this, remove all indi-
vidual parts from the box and compare them with the fol-
lowing list.
- Sanding belt grit 60
- Operating instructions
- Suction nozzle adapter 35 to 120mm
- Grinding wheel grit 80 (glued on)
6.2 Accessories
- Base
Item number: 5914250
- Abrasive sheet Ø250 K150, adhesive-backed
Item number: 5912515
- Abrasive sheet Ø250 K120, adhesive-backed
Artikelnummer: 5912512
- Abrasive sheet Ø250 K100, adhesive-backed
Item number: 5912510
- Abrasive sheet Ø250 K80, adhesive-backed
Item number: 5912508
- Abrasive sheet Ø250 K60, adhesive-backed
Item number: 5912506
- Velcro pad Ø250, self-adhesive
Item number: 5912501
- Sanding belt with paper backing 1219x150 K180
Item number: 5911218
- Sanding belt with paper backing 1219x150 K120
Item number: 5911212
- Sanding belt with paper backing 1219x150 K100
Item number: 5911210
- Abrasive belt with paper backing 1219x150 K80
Item number: 5911208
- Abrasive belt with paper backing 1219x150 K60
Item number: 5911206
- Angle stop
Item number: 5914251
WARNING!
The use of unstable lifting and load suspension
equipment that might break under load can cause
severe injuries or even death. Check that the lifting
and load suspension gear has sufficient load-bea-
ring capacity and that it is in perfect condition.
Observe the accident prevention regulations issued
by your Employers Liability Insurance Association or
other competent supervisory authority, responsible
for your company.
Fasten the loads properly.
WARNING: DANGER OF TIPPING
The device may be lifted unsecured by a maximum
of 2cm.
Employees must be outside the danger zone, the
reach of loads.
Warn employees and, if necessary, advise employ-
ees of the hazard.