Holzstar 5904150 Скачать руководство пользователя страница 5

Safety

BTS-Series | Version 3.06

5

2.3 Qualification of personnel

The different tasks described in this manual represent 
different requirements to the qualification of the persons 
entrusted with these tasks.  

Only persons reliable working procedures can be ex-
pected from, are allowed to perform all works. Persons 
the responsiveness of which is affected by e. g. drugs, 
alcohol or medication, are not allowed to work with the 
machine. 

The qualifications of the personnel for the different tasks 
are mentioned below:

Operator:

The operator is instructed by the operating company 
about the assigned tasks and possible risks in case of 
improper behaviour. Any tasks which need to be perfor-
med beyond the operation in the standard mode must 
only be performed by the operator if it is indicated in 
these instructions and if the operating company expres-
sively commissioned the operator.

Electrical specialist:

Due to his professional training, knowledge and experi-
ence as well as his knowledge of respective standards 
and regulations the electrical specialist is able to perform 
works on the electrical system and to recognise and 
avoid any possible dangers himself.

Specialist staff:

Due to their professional training, knowledge and experi-
ence as well as their knowledge of relevant regulations 
the specialist staff is able to perform the assigned tasks 
and to recognise and avoid any possible dangers them-
selves.

Manufacturer:

Certain works may only be performed by specialist per-
sonnel of the manufacturer. Other personnel is not au-
thorized to perform these works. Please contact our cus-
tomer service for the execution of all arising work..

2.4 Personal protective equipment

The personal protective equipment serves to protect per-
sons against impairments of safety and health while wor-
king. The staff has to wear personal protective equip-
ment while performing different works on and with grind-
ing system which are indicated in the individual paragra-
phs of these instructions. 

The personal protective equipment is explained in the 
following paragraph:

WARNING!

Danger in case of insufficient quali-
fication of the staff!!

Insufficiently qualified persons cannot estimate the 
risks while using machine and expose themselves 
and others to the danger of severe injuries.  

-  Have all works only performed by qualified persons.

-  Keep insufficiently qualified persons and children 

out of the working area.

Ear and head protection 

The hearing protection protects the ears against 
damages of hearing due to noise. The industrial hel-
met protects the head against falling objects and 
bumping into fixed objects.

Eye protection

The protective goggles protect the eyes against parts 
flying off and splashes of liquids. 

Breathing protection

The breathing protection serves for protecting the 
respiratory passages and the lung against the intake 
of dust particles.

Protective gloves

The protective gloves serve to protect the hands 
against sharp components as well as against friction, 
abrasions or deep injuries.

Safety boots

The safety boots protect the feet against crushes, fal-
ling parts and slipping over on slippery underground. 

Protective clothes

The protective clothes are tight clothes of little tensile 
strength.

Содержание 5904150























Отзывы: