manualshive.com logo in svg

Holtek HT66F2740, Руководство пользователя, Страница: 170 / 202

Поделиться
Скачать
Holtek HT66F2740 Скачать руководство пользователя страница 170

Rev. 1.20

170

November 20, 2019

Rev. 1.20

171

November 20, 2019

HT66F2740

12V High Current Flash MCU

HT66F2740

12V High Current Flash MCU

TM Interrupt vector locations, will take place. When the TM Interface Interrupt is serviced, the TM 

interrupt request flag will be automatically reset and the EMI bit will be cleared to disable other 

interrupts.

LVD Interrupt

An LVD Interrupt request will take place when the LVD Interrupt request flag, LVF, is set, which 

occurs when the Low Voltage Detector function detects a low power supply voltage. To allow the 
program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, 

and Low Voltage Interrupt enable bit, LVE, must first be set. When the interrupt is enabled, the stack 

is not full and a low voltage condition occurs, a subroutine call to the LVD Interrupt vector, will 

take place. When the LVD Interface Interrupt is serviced, the interrupt request flag, LVF, will be 

automatically reset and the EMI bit will be cleared to disable other interrupts.

A/D Converter Interrupt

An A/D Converter Interrupt request will take place when the A/D Converter Interrupt request flag, 
ADF, is set, which occurs when the A/D conversion process finishes. To allow the program to branch 

to its respective interrupt vector address, the global interrupt enable bit, EMI, and A/D Interrupt 

enable bit, ADE, must first be set. When the interrupt is enabled, the stack is not full and the A/D 

conversion process has ended, a subroutine call to the A/D Interrupt vector, will take place. When 

the A/D Converter Interrupt is serviced, the A/D Interrupt flag, ADF, will be automatically cleared. 

The EMI bit will also be automatically cleared to disable other interrupts.

EEPROM Interrupt

An EEPROM Interrupt request will take place when the EEPROM Interrupt request flag, DEF, is set, 

which occurs when an EEPROM Write cycle ends. To allow the program to branch to its respective 
interrupt vector address, the global interrupt enable bit, EMI, and EEPROM Interrupt enable bit, 

DEE, must first be set. When the interrupt is enabled, the stack is not full and an EEPROM Write 

cycle ends, a subroutine call to the EEPROM Interrupt vector will take place. When the EEPROM 

Interface Interrupt is serviced, the interrupt request flag, DEF, will be automatically reset and the 

EMI bit will be cleared to disable other interrupts.

Time Base Interrupts

The function of the Time Base Interrupts is to provide regular time signal in the form of an internal 

interrupt. They are controlled by the overflow signals from their respective timer functions. When 

this

 happens their respective interrupt request flags, TB0F or TB1F will be set. To allow the program 

to branch to their respective interrupt vector addresses, the global interrupt enable bit, EMI and 

Time Base enable bits, TB0E or TB1E, must first be set. When the interrupt is enabled, the stack is 
not full and the Time Base overflows, a subroutine call to their respective vector locations will take 
place. When the interrupt is serviced, the respective interrupt request flag, TB0F or TB1F, will be 

automatically reset and the EMI bit will be cleared to disable other interrupts. 

The purpose of the Time Base Interrupt is to provide an interrupt signal at fixed time periods. Its 

clock source, f

PSC

, originates from the internal clock source f

SYS

, f

SYS

/4 or f

SUB

 and then passes 

through a divider, the division ratio of which is selected by programming the appropriate bits in the 
TB0C and TB1C registers to obtain longer interrupt periods whose value ranges. The clock source 
which in turn controls the Time Base interrupt period is selected using the CLKSEL1~CLKSEL0 
bits in the PSCR register.

Содержание HT66F2740











































































































































































































Отзывы:

Нет отзывов