Hoffmann MS35-SF-TP Скачать руководство пользователя

Страница: 2 / 114

Operating and Maintenance Manual

HOFFMANN MS35SF-TP

Double Miter Saw

• Version 7.148.66 • 06-2017

Table of contents

WARNING AND SAFETY SYMBOLS USED IN THIS MANUAL ........................................................... 4

2.1

WARNING AND SAFETY LABELS ATTACHED TO MACHINE ........................................................... 5

INTENDED USE AND OPERATION ....................................................................................................... 7

MACHINE DESCRIPTION ....................................................................................................................... 9

4.1

Terminology used in this manual ................................................................................................... 9

TECHNICAL DATA AND SPECIFICATIONS........................................................................................10

OPERATOR ENVIRONMENT................................................................................................................11

POTENTIALLY DANGEROUS AREAS ................................................................................................12

POTENTIAL SOURCES OF DANGER ..................................................................................................13

8.1

Unapproved Use ..........................................................................................................................13

8.2

Mechanical Dangers.....................................................................................................................13

8.3

Defective equipment.....................................................................................................................14

8.4

Electrical Dangers ........................................................................................................................14

8.5

Cleaning agents and chemicals ...................................................................................................14

NOISE EMISSIONS ...............................................................................................................................16

GENERAL SAFETY RULES IN ACCORDANCE WITH DIN 1870-9 ....................................................17

SAFETY DEVICES .................................................................................................................................20

11.1

Safety Devices .............................................................................................................................21

11.2

What to do in an Emergency? ......................................................................................................22

11.3

Safety device check list ................................................................................................................23

WARRANTY AND LIABILITY................................................................................................................24

TRANSPORTATION AND INSTALLATION ..........................................................................................25

13.1

Transportation ..............................................................................................................................25

13.2

Installation and Set-Up .................................................................................................................27

13.3

Machine installation diagram ........................................................................................................28

13.4

Electrical and compressed air connections ..................................................................................29

13.4.1

Connecting electrical enclosure to power supply .........................................................30

13.4.2

Compressed air connections ........................................................................................31

13.4.3

Check Connections .......................................................................................................32

13.4.4

Installation of infeed and outfeed tables and fence rails...............................................33

13.4.5

Dust collection connections ..........................................................................................34

OPERATION

– WARNINGS AND SAFETY RULES .............................................................................35

14.1

Initial start-up ................................................................................................................................36

14.2

Tooling change .............................................................................................................................37

14.2.1

Opening machine front cover ........................................................................................37

14.2.2

Saw blade change ........................................................................................................38

14.2.3

Chip breaker (table insert) change ...............................................................................39

14.2.4

Router bit installation and adjustments (with set-up jig) ...............................................40

14.3

Router bit adjustments .................................................................................................................41

14.3.1

Router bit adjustments (with caliper) ............................................................................42

14.2 Adjustment of keyway positions ..................................................................................43

Содержание MS35-SF-TP



















































































































Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды

Hoffmann MS35-SF-TP, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды