Hoffmann MS35-SF-TP Скачать руководство пользователя | Manualshive

Страница: 77 / 114

background image

Operating and Maintenance Manual

HOFFMANN MS35SF-TP Double Miter Saw

• Version 7.148.66 • 06-2017

77

14. Law Governing:
Buyer’s  purchase  order  shall  be  governed  by  and  construed  according  to  the  laws  of  the  State  of  North
Carolina.  The  courts  of  the  State  of  North  Carolina  shall  have  jurisdiction  over  any  controversy  that  may
arise out of the dealings between Buyer and Seller.

15. Force Majure:
Seller  shall  not  be  liable  under  this  agreement  by  reason  of  its  delay  in  the  performance  of  or  failure  to
perform  any  of  its  obligations  hereunder  if  such  delay  or  failure  is  caused  by  acts  of  God  or  the  public
enemy, riots, incendiaries, interference by civil or military authority, compliance with government laws, rules
and regulations or any fault beyond its control.

16. Acceptance:
Payment  for  or  a  deposit  made  for  the  products  shall  constitute  a  contract  embodying  all  of  terms  and
conditions stated herein.

17. Ownership:
All products remain the sole property of the Seller until all charges, including all transportation, crating and
installation costs, are paid in full.

18. Severability:
The provisions of these Terms and Conditions are intended to be severable. If, for any reason, any of the
above  provisions  should  be  found  unenforceable  or  invalid  in  whole  or  in  part,  in  any  jurisdiction,  such
provision  be  ineffective  only  to  the  extend  the  determination  of  invalidity  or  unenforceability  in  that
jurisdiction. Any such determination shall not affect the enforceability or validity of the remaining provisions.

«
...
75
76
77
78
79
...
»

Содержание MS35-SF-TP



















































































































Отзывы:

Нет отзывов

Похожие инструкции для MS35-SF-TP

Бренд: Jet Страницы: 28

Бренд: Way Train Страницы: 43

MetalMaster BS-5S

Бренд: Hafco Страницы: 27

Бренд: PrimAster Страницы: 40

Бренд: Milwaukee Страницы: 9

Бренд: Felisatti Страницы: 40

Бренд: Jet Страницы: 18

430-03-651-0005

Бренд: Delta Страницы: 16

Бренд: Partner Страницы: 23

M18 FUEL FMS305

Бренд: Milwaukee Страницы: 12

Бренд: 6K Products Страницы: 12

Бренд: Kobalt Страницы: 48

Бренд: Sioux Tools Страницы: 4

Бренд: Worx Страницы: 132

Бренд: Westfalia Страницы: 54

Бренд: sunjoe Страницы: 20

FATMAX V20 SFMCS310

Бренд: Stanley Страницы: 96

Бренд: Echo Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды