Hoffmann MS35-SF-TP Скачать руководство пользователя | Manualshive

Страница: 12 / 114

background image

Operating and Maintenance Manual

12

HOFFMANN MS35SF-TP

Double Miter Saw

• Version 7.148.66 • 06-2017

7

Potentially Dangerous Areas

Especially dangerous areas of the machine are:



Areas around the miter cutting operations



Areas around the dovetail routing operations

During set-up and maintenance procedures, the
following dangers exist in the above areas:

Danger of entanglement and pinching!

During set-up and maintenance work,
especially when access doors must be
opened, additional dangers of
entanglement or pinching on belts,
sprockets, saw station, router station,
drilling station, etc. are present. Do not
wear loose fitting clothing. Long hair must
be covered with a hair net.

Danger of cutting of hands and fingers!

All sawing, routing and drilling areas
present dangers of cutting of hands and
fingers.

Danger of amputation!

All sawing areas present the danger of
severe cutting or amputation of fingers.

«
...
10
11
12
13
14
...
»

Содержание MS35-SF-TP



















































































































Отзывы:

Нет отзывов

Похожие инструкции для MS35-SF-TP

Бренд: Felisatti Страницы: 104

Бренд: Fein Страницы: 162

Бренд: Mainca Страницы: 29

Бренд: Fieldmann Страницы: 99

Бренд: F.F. Group Страницы: 28

Бренд: Diamond Products Страницы: 44

Бренд: Ryobi Страницы: 73

Бренд: Clearmount Страницы: 6

Бренд: Maktec Страницы: 12

Бренд: SSP Страницы: 12

Бренд: South Bend Tools Страницы: 88

Бренд: Tomahawk Страницы: 21

Бренд: Hitachi Страницы: 88

Бренд: Hitachi Страницы: 84

Бренд: Hitachi Страницы: 132

Бренд: Hitachi Страницы: 96

Бренд: Hitachi Страницы: 72

Бренд: Hitachi Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды