Hoffmann MS35-SF-TP Скачать руководство пользователя

Страница: 17 / 114

Operating and Maintenance Manual

HOFFMANN MS35SF-TP Double Miter Saw

• Version 7.148.66 • 06-2017

General Safety Rules in accordance with DIN 1870-9

DANGER: The following safety rules must
be followed at all times!

Read and understand this operator manual thoroughly and store it
in a safe place for future reference.

Heed all safety warnings and all applicable rules and regulations,
including but not limited to all applicable OSHA rules, when
operating or performing maintenance or set-up procedures on this
equipment.

1. HOFFMANN Service Technicians will instruct machine operators in the

proper use of this equipment upon installation and set-up.

2. The HOFFMANN

MS35SF-TP

double miter saw may only be operated

by trained personnel who have read and understood the operator

manual. The manual shall be kept in a safe location, easily accessible

for future reference.

3. Only trained and authorized persons may be allowed to operate the

HOFFMANN

MS35SF-TP

double miter saw. Untrained or

unauthorized persons are to be kept away from the machine area. The

operator(s) must disconnect the electrical and pneumatic power

supplies when the machine is not under their control.

4. All applicable Safety Rules, including all applicable OSHA rules, are to

be adhered to.

5. Only trained and qualified persons may perform work on the electrical

components of the machine.

6. Before connecting the HOFFMANN

MS35SF-TP

double miter saw to

the electrical power supply, all electrical specifications must be
confirmed with the machine’s data sheet.

7. Never disable, remove or bypass any safety features, guards or

devices!

8. HOFFMANN

MS35SF-TP

double miter saw may only be energized if

no danger for persons or materials is present.

9. All safety features, guards and safety devices must be checked for

proper function at least every three months (always follow

recommended maintenance schedule).

10. Upon discovery of any damage to any part or component of

HOFFMANN

MS35SF-TP

double miter saw, the machine must be

shut off and locked to prevent further operation until all damager and/or

faults are repaired.

11. The operator must inform his or her supervisor immediately upon notice

of any damage or fault on the machine.

Содержание MS35-SF-TP



















































































































Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды

Hoffmann MS35-SF-TP, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MS35-SF-TP

Отзывы:

Похожие инструкции для MS35-SF-TP

Бренды по названию

Популярные бренды