Hoffmann MS35-SF-TP Скачать руководство пользователя | Manualshive

Страница: 24 / 114

background image

Operating and Maintenance Manual

24

HOFFMANN MS35SF-TP

Double Miter Saw

• Version 7.148.66 • 06-2017

12

Warranty and Liability

The „Hoffmann Machine Company, Inc. Terms and Conditions of Sale
“are the basis for all dealings between the manufacturer and the
customer. These Terms have been made available to the customer
during the proposal and order processing stage.

In addition to the complete Terms and Conditions of Sale, any of the
following conditions immediately voids the warranty and releases the
manufacturer from any and all liability.



Unapproved use of the machine.



Improper installation, start-up, maintenance or operation

of the machine.



Operation of machine with defective, missing or by-

passed safety devices of any kind.



Non adherence to any rule or regulation in this operator

manual.



Unauthorized changes to the machine or any of its

components as well as unauthorized changes to control
parameter (changes to PLC program, etc.)



Insufficient supervision and maintenance of parts subject

to normal wear and tear.



Damage due to unforeseen circumstances, acts of God,

etc.



Improper or unauthorized repairs.

«
...
22
23
24
25
26
...
»

Содержание MS35-SF-TP



















































































































Отзывы:

Нет отзывов

Похожие инструкции для MS35-SF-TP

Бренд: Zenoah Страницы: 18

Бренд: Ratio Страницы: 48

Бренд: Ferm Страницы: 108

Бренд: Jet Страницы: 17

Бренд: Parkside Страницы: 74

Craftsman 113.235100

Бренд: Sears Страницы: 32

Бренд: EINHELL Страницы: 46

WorxSaw WX523.9

Бренд: Worx Страницы: 24

Бренд: Worx Страницы: 144

Бренд: Echo Страницы: 4

Power Pruner 99946400010

Бренд: Echo Страницы: 8

Бренд: Scheppach Страницы: 90

Бренд: Scheppach Страницы: 144

Бренд: Scheppach Страницы: 276

Бренд: Scheppach Страницы: 122

Бренд: Workzone Страницы: 28

Бренд: Power Craft Страницы: 10

Бренд: Power Craft Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды