8 Channel 2.4 GHz Aircraft Computer Radio System
8 Channel 2.4 GHz Aircraft Computer Radio System
Section 5: Acro and Glider Programming Menu
Section 5: Acro and Glider Programming Menu
74
75
Elevator to Camber Mixing cont.
14. Scroll to highlight the “SPEED” field and press the jog dial to
activate the menu.
15. Rotate the jog dial to increase or decrease the transit time of
the wing servos (in seconds) when operating with the mix. Press
the jog dial to confirm your input.
16. Scroll to highlight the “TRIM” field and press the jog dial to
activate the menu.
17. Rotate the jog dial to select “ON” or “OFF” and press the jog
dial to confirm your selection. When “ON” is selected, the mix
reacts to trim adjustments of the elevator. Otherwise, the mix
ignores elevator trim changes.
18. If the model is equipped with flaps, scroll to the function field
(“AILE” or “FLAP”) and press the jog dial to activate the menu.
Otherwise, skip to step 21.
19. Rotate the jog dial to select “FLAP” and press the jog dial to
confirm your selection.
20. Repeat steps 6-17 to configure the flap movements for this mix. If using only one flap servo, configure
only the “FLAP” row of the value table. If using two flap servos, configure both rows of the value table.
22. Rotate the jog dial to select a switch to activate the mix. Press
the jog dial to confirm your selection.
a. If you choose the “NULL” option, the mix will remain active at
all times for this model.
b. If you choose a switch:
- The switch position menu will appear. Scroll to highlight the
switch position that you will use to enable the mix. Press the jog
dial to confirm your selection.
21. Scroll to the “S/W” field and press the jog dial twice to
activate the menu.
- Scroll to select “ON” and press the jog dial to confirm your
selection. If you toggle the selected switch, the field in the top
right corner of the screen will indicate when the mix is active.
23. Press the back button to return to the model function menu.
If you are using multiple flight conditions, you must define elevator-camber mix values for each flight
condition. The top field of the ELEV-CAMB menu allows you to select the desired flight condition.
Alternately, you may select the desired flight condition using the assigned F.Cond switch.
To disable the elevator-to-camber mix:
1. Scroll to highlight the “MIX” field in the elevator-camber mix
menu and press the jog dial to activate the menu.
2. Select “INH” (inhibit) and press the jog dial to confirm your
selection.
3. Press the back button to return to the model function menu.
Elevator to Camber Mixing cont.
Warning
Note
Tip
Tip
Tip
Caution
To configure the camber mix:
1. From the Model menu, rotate the jog dial to highlight “Camber
Mix” and press the jog dial once to enter the activation menu.
2. Press the jog dial again to activate the menu.
3. Rotate the jog dial to select “ACT” (activate), then press the
jog dial to confirm your selection and activate the camber mix
menu.
Camber Mix
The Camber Mix feature allows you to define the camber of the wing airfoil by raising or lowering the
wing control surfaces in unison. You may also adjust the elevator neutral position in each setting to
maintain proper pitch trim.
24. To set-up Elevator to Camber mixing in accordance with a
Flight Condition:
− The upper right field of the menu displays which flight
condition is currently active and will be programmed.
− Scroll to the Flight Condition field and press the jog dial to
activate the menu.
− Choose the desired flight condition and press the jog dial to
confirm your selection.
25. Press the back button to return to the model function menu.
4. Scroll to highlight the “AILE” field and press the jog dial to
activate the menu.
5. Rotate the jog dial to input the desired travel for the “AILE” servo
when camber is active. Press the jog dial to conform your input.
