Hitachi Summit RAC-70YH5 Скачать руководство пользователя

Страница: 45 / 102

Notes:

(1)

The sleep operation starts when the sleep key is pressed.

(2)

When the sleep key is set, the maximum compressor speed is limited, and the indoor fan is set to “sleep Lo”.

(3)

30 minutes after the sleep key is set, the sleep shift of temperature starts, and upper shift is made at least 6
times. If 25˚C is not reached after 6 shifts, shifts repeat unit 25˚C is reached.

(4)

The sleep shift upper value of set temperature is 28˚C.

(5)

After 6 hours, a shift down to the initial set temperature is made at a rate of 0.33˚C/5 min.

(6)

If the operation mode is changed during sleep operation, the set temperature is cleared, and shift starts from the
point when switching is made.

(7)

The indoor fan speed does not change even when the fan speed mode is changed.

(8)

When operation is stopped during sleep operation, the set temperature when stopped, as well as the time,
continue to be counted.

(9)

If the set lime is changed during sleep operation, all data including set temperature, time, etc. is cleared and
restarted.

(10) If sleep operation is canceled by the cancel key or sleep key, all data is cleared.

Compressor speed

Horizontal air
deflector

Shut

Horizontal

Facing down

Maximum speed

Indoor fan

Outdoor fan

Timer lamp

Operation lamp

Sleep key

(Cooling/dehumidifying set
temperature = Remote control set
temperature (+) SHIFTC)

Final set temperature
(Cooling/dehumidifying set
temperature (+) sleep shift)

Set to 7 hours

0.5hr

1.5hr

3hr

2.5hr

3.5hr

6hr

7hr

See basic operation

Med

Lo (sleep)

10 mins

Cooling Sleep Operation

– 49 –

0305E Pg 49

4/1/06, 10:56 AM

Содержание Summit RAC-70YH5







































































































Результаты поиска

Содержание Summit RAC-70YH5

Отзывы:

Похожие инструкции для Summit RAC-70YH5

Бренды по названию

Популярные бренды

Hitachi Summit RAC-70YH5, Руководство по обслуживанию

Результаты поиска

Содержание Summit RAC-70YH5

Отзывы:

Похожие инструкции для Summit RAC-70YH5

Бренды по названию

Популярные бренды