Hitachi Summit RAC-70YH5 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 102

background image

– 13 –

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C.
When it is under 15°C, the dehumidifying function will not work.

■

Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the room,
reducing the room temperature to the preset level.
When the room temperature is lower than the temperature setting: Dehumidifying will be performed at
the temperature setting slightly lower than the current room temperature, regardless of the temperature
setting. The function will stop (the indoor unit will stop emitting air) as soon as the room temperature
becomes lower than the setting temperature.

Set the desired room temperature with the TEMPERATURE
button (the display indicates the setting).

The range of 20-26˚C is recommended as
the room temperature for dehumidifying.

Press the

(START/STOP) button. Dehumidifying operation

starts with a beep. Press the button again to stop operation.

2

■

As the settings are stored in memory in the remote controller, you
only have to press the

(START/STOP) button next time.

START

STOP

Press the FUNCTION selector so that the display indicates

(DEHUMIDIFY).

The FAN SPEED is set at LOW automatically.
The FAN SPEED button does not work.

1

RESET

˚

C

˚

C

0305E Pg 06-15

4/1/06, 10:48 AM

13

«
...
13
14
15
16
17
...
»

Содержание Summit RAC-70YH5







































































































Отзывы:

Нет отзывов

Похожие инструкции для Summit RAC-70YH5

Бренд: NEC Страницы: 15

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 297

Бренд: Lasko Страницы: 6

Бренд: Better Air Страницы: 2

Бренд: Daikin Страницы: 18

Бренд: BOMANN Страницы: 74

Бренд: EQUATION Страницы: 45

Бренд: TriStar Страницы: 12

Бренд: thermital Страницы: 24

Бренд: MAXA Страницы: 48

Бренд: Midea Страницы: 19

Бренд: Technibel Страницы: 54

Бренд: Hawk Страницы: 2

bycool green line SLIM COOL TRR

Бренд: dirna Bergstrom Страницы: 68

Бренд: ARDES Страницы: 20

Duplex Water-Cooled Hermetic CenTraVac

Бренд: Trane Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды