Hitachi Summit RAC-70YH5 Скачать руководство пользователя страница 14

Страница: 14 / 102

– 12 –

HEATING OPERATION

●

Use the device for heating when the outdoor temperature is under 21°C.
When it is too warm (over 21°C), the heating function may not work in order to protect the device.

●

In order to keep reliability of the device, please use this device above -15°C of the outdoor temperature.

Press the FUNCTION selector so that the display indicates
(HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button
(the display indicates the setting).

(AUTO): The fan speed is HI at first and varies to MED

or LOW automatically when the preset
temperature has been reached.

(HI)

: Economical as the room will become warm

quickly.
But you may feel a chill at the beginning.

(MED) : Fan speed slow.

(LOW) : Fan speed slower.

Set the desired room temperature with the TEMPERATURE
buttons (the display indicates the setting).

The temperature setting and the actual room temperature may
vary somewhat depending on conditions.

Press the (START/STOP) button. Heating operation starts
with a beep. Press the button again to stop operation.

■

As the settings are stored in memory in the remote controller, you only
have to press the (START/STOP) button next time.

START

STOP

RESET

0305E Pg 06-15

4/1/06, 10:48 AM

Содержание Summit RAC-70YH5







































































































Результаты поиска

Содержание Summit RAC-70YH5

Отзывы:

Похожие инструкции для Summit RAC-70YH5

Бренды по названию

Популярные бренды

Hitachi Summit RAC-70YH5, Руководство по обслуживанию

Результаты поиска

Содержание Summit RAC-70YH5

Отзывы:

Похожие инструкции для Summit RAC-70YH5

Бренды по названию

Популярные бренды