Hitachi SJ100 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 75

background image

(4) Over voltage (E 07)

Phenomena:

Over voltage at DC bus line of the frequency inverter.

Cause:

Mains voltage too high, mains voltage fluctuation or rapid mains voltage return
(choke energy leads to voltage increase).

Remedy:

Make sure that mains voltage is within tolerance limits.

Cause:

In case SJ100 is used in combination with a regenerative braking unit(ISPM)/
resistor but the regenerative braking unit(ISPM)/resistor does not function.

Remedy:

Replace regenerative braking unit(ISPM)/resistor.

Cause:

In case SJU100 is used in combination with a raking resistor but the braking
resistor cannot absorb the regenerative energy.

Remedy:

Re-calculate and use suitable braking resistor.

Cause:

Deceleration time is too short.

Remedy:

Make deceleration time longer, use braking unit (resistor), use bigger capacity of
frequency inverter.

Way to Reset:

A

(5) Under voltage (E 09)

Phenomena:

Under voltage at DC bus line of the frequency inverter.

Cause:

The mains voltage is not available or not within the tolerance limits.

Remedy:

Check all 3 (or 2) mains power supply voltage that it is within its specification.

Cause:

Thyristor for smooth charging is defect and DC bus voltage drops while operation
due to current flows through smooth charging resistor.

Remedy:

Change ISPM.

Cause:

Period of instantaneous power failure is longer than the set value [b02], or DC bus
voltage go down to its detecting level while instantaneous power failure.

Remedy:

Get rid of the instantaneous power failure, evaluate the power supply system, set
bigger value for [b02].

Cause:

One of the AC voltage is missing (applied only for 3 phase INV)

Remedy:

Check AC line voltage , check the fuses.

Way to Reset:

A

(6) EEPROM error (E 08)

Phenomena:

Abnormal situation occurs at the memory portion of the frequency inverter due to
incoming noise etc..

Cause:

Influenced by Electrical Magnetic Interference.

Remedy:

Keep such noise source away from the frequency inverter.

Cause:

Ambient temperature is too high.

Remedy:

Take countermeasure against high ambient temperature.

3-3

«
...
12
13
14
15
16
...
»

Содержание SJ100 Series












































































Отзывы:

Нет отзывов

Похожие инструкции для SJ100 Series

Бренд: ultimatte Страницы: 125

Бренд: 3One data Страницы: 9

Бренд: D&H Страницы: 70

Бренд: Underhill Страницы: 30

Бренд: Lenze Страницы: 132

Бренд: Datalogic Страницы: 2

ENC58-H15 Series

Бренд: Datalogic Страницы: 2

Бренд: ScienTECH Страницы: 12

Бренд: D&R Страницы: 17

Бренд: Radial Engineering Страницы: 12

Бренд: Pentax Страницы: 44

Бренд: Bogen Страницы: 7

Бренд: Phrontier Technologies Страницы: 16

Бренд: La Boite Concept Страницы: 52

Бренд: Alloy Страницы: 9

Extron Electonics YCV 100

Бренд: CAMBOARD Страницы: 12

FCM 300 PROFIBUS

Бренд: Danfoss Страницы: 39

Бренд: MultiDyne Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды