Hitachi RAC-E50YHA страница 35 Скачать руководство пользователя

Страница: 35 / 35

12.6 TEST RUN

After completing the installation of the air panel, the test run
should be performed.

Perform the checking work for the louvre during the test run.

Do not move the louvre by hand. If moved, the auto-swing
mechanism will be damaged.

12.7 ADJUSTING LOUVRES

N O T E

•

The adequate air flow direction may differ depending on the conditions

(air conditioner’s installation position, room structure or furniture

layout, etc.) If the cooling or the heating is not well, adjust the air flow

direction.

•

If the cooling operation is performed under the condition with over

80% humidity, dew condensation may occur at the air panel or the

louvre.

C A U T I O N

Do not move the louvre by hand. If moved, the louvre mechanism will be

damaged. In addition, do not apply an excessive force to the air outlet part

to prevent the breakage.

Louver

Louvre

13 OPTIONAL PART

13.1 OPTIONAL PART CONNECTION FOR INDOOR UNIT

CN1102

CN9

CN11A

CN1101

Wireless remote

controller cord

Wifi adaptor /

RAC adaptor cord

DRY contact

cord

Wired remote

controller cord

•

To connect via H-LINK, a separately purchased RAC

Adaptor is required.

•

To connect to Dry Contact, a separately purchased Dry

Contact Connection Cord is required.

•

The Wired Remote Controller to be connected in the

CN1102 port is sold separately.

•

To connect via WiFi, a separately purchased WiFi

Adaptor is required.

•

The Wireless Remote Controller to be connected in the

CN11A port is sold separately.

•

Remove the metal cover of the electrical box in order to
connect the wiring of the respective devices.

•

For Dry Contact, connect the connection cord to CN9.

•

For WiFi Adaptor or RAC Adaptor, connect the connection
cord to CN1101.

•

For Wired Remote Controller, connect the connection cord to
CN1102.

•

For Wireless Remote Controller, connect the connection cord
to CN11A.

•

The connection cords and power cable are to be arranged
and tied up as shown in the diagram above.

•

Please refer to the respective user manual of the Dry
Contact, WiFi Adaptor, RAC Adaptor, Wireless Remote
Controller and Wired Remote Controller for further details.

•

Please refer to user manual for instructions on installation
and maintenance of the electrical box.

•

Please be careful not to damage lead wires by with the edge
of the metal plates when connecting the optional parts.

•

Please refer to the catalogue for part numbers when ordering
any optional part.

OPTIONAL PART

PMML0477 rev.1 - 10/2017

Содержание RAC-E50YHA




































Результаты поиска

Содержание RAC-E50YHA

Отзывы:

Похожие инструкции для RAC-E50YHA

Бренды по названию

Популярные бренды

Hitachi RAC-E50YHA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RAC-E50YHA

Отзывы:

Похожие инструкции для RAC-E50YHA

Бренды по названию

Популярные бренды