Hitachi RAC-E50YHA Скачать руководство пользователя

Страница: 30 / 35

ENGLISH

12 INSTALLATION OF OPTIONAL AIR PANEL: P-AP56NAM

12.1 APPLICABLE MODEL

This air panel is applicable to the following indoor unit model:

Air panel

Indoor unit model

P-AP56NAM

RAI-

YHA

, RAI-

YHA

12.2 TRANSPORTATION AND HANDLING

Transport the air panel without unpacking as close to the
installation location.

Mount the air panel as soon as possible after unpacking.

When the air panel is placed on the floor after unpacking,
place it with the rear side downward (the surface to fit the

indoor unit body) on an insulation material, etc. However,

do not leave the air panel on the floor for long time. It may

cause air leakage due to scratch the seal packing.

In addition, if the air panel is placed with the surface
downward, the louvre mechanism may be damaged due to

touch the louvre to the floor, etc.

Do not move the louvre by hand. If moved, the louvre
mechanism will be damaged.

12.3 BEFORE INSTALLATION

Check to ensure that the following accessories are packed with the air panel.

Name

Quantity

Purpose

Long Screw (M5 Cross Screw)

For fixing air panel

If any of these accessories are not packed in the packing, please contact your contractor.

12.3.1 Motion sensor (optional accessory)

Motion sensor detects the human activity by measuring the
level of change in infrared light emitted by humans or objects.
Therefore, the misdetection or undetectable of the motion may
occur under the following situations.

No alternation of temperature or movement of heat
source in the detection area.

Obstruction such as glass impervious to infrared light in
the detecting area.

Heat source moves rapidly in the detecting area.

Someone is in a room with a little motion.

Ceiling height is 2.7 meters or more.

Person is facing their back against the motion sensor or
exposure of the skin is less.

It may be difficult for the motion sensor to detect human

activity on the border of the detection area.

The sensing area for the motion sensor is shown in the figure
below when applying the motion sensor with the air panel:

Motion Sensor

from Floor Surface
0.8m

Motion sensor

0.8m from floor surface

Installation height of indoor unit: h (m)

2.7

Sensing area for motion sensor:

a (m)

Approx. 5.0

INSTALLATION OF OPTIONAL AIR PANEL: P-AP56NAM

PMML0477 rev.1 - 10/2017

Содержание RAC-E50YHA




































Результаты поиска

Содержание RAC-E50YHA

Отзывы:

Похожие инструкции для RAC-E50YHA

Бренды по названию

Популярные бренды

Hitachi RAC-E50YHA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RAC-E50YHA

Отзывы:

Похожие инструкции для RAC-E50YHA

Бренды по названию

Популярные бренды