Hitachi DKC910I Скачать руководство пользователя страница 66

Страница: 66 / 138

DKC910I

Hitachi Proprietary

[INST(RM)06-01-30]

Rev.0

INST(RM)06-01-30

(3) <Disk Board Removal Execution Window>

About

“

Forcibly run without safety checks

”

If you check this checkbox and execute the maintenance, the system may go down. Do not

check it unless instructed by the message, the manual or the contact described in the manual.

About

“

Forcibly block

”

If you check this checkbox and execute the maintenance, the system may go down. Do not

check it unless instructed by the contact described in the manual.

Check the Disk Boards to be removed and click [Remove].

NOTE : The error list window is displayed if multiple errors are detected by the prior check.

If it is displayed, click the text of

“

Error Code

”

and recover the failures or the

blockade in accordance with the details of the displayed errors.

(4) <Displaying the Password entry window>

This operation may cause a serious error such as a system down or a data loss. Conﬁrm the

appropriateness of the operation, and then input of the password.

Enter the login password for the maintenance account of the storage system, and then click [OK].

Содержание DKC910I










































































































































Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды

Hitachi DKC910I, Руководство по установке

Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды