Hitachi DKC910I Скачать руководство пользователя страница 117

Страница: 117 / 138

DKC910I

Hitachi Proprietary

[INST(RM)10-04-90]

Rev.2

INST(RM)10-04-90

10.

Removing Rails

NOTE: • There are the rail (R) and the rail (L). Check that with the marking on the rail.

• These rails extend or shorten back and forth.
• Thease are the rail type with a stopper and the rail type without a stopper.

(1) Remove the screw (M5

10), loop cable tie and the LL washer from the rear side of right rail.

(2) Open two Clips located in the front and the rear side of right rail
(3) Push the rail that is mounted at the right side of the rack frame and remove the Positioning Pin on

the front side of the rail. Then remove the rail from the rack frame.

(4) Remove the left side rail from the rack frame in the same way.
(5) Remove rack nuts or cage nuts from the rack frame.

Figure 10-8 Removing Rails

Rack frame (rear side)

Screw (M5

10)

Clip

Rail (R)

Rack frame (front side)

Cate nut or rack nut

LL washer

Cage nut or rack nut

Loop cable tie

Содержание DKC910I










































































































































Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды

Hitachi DKC910I, Руководство по установке

Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды