Hitachi DKC910I Скачать руководство пользователя страница 123

Страница: 123 / 138

DKC910I

Hitachi Proprietary

[INST(RM)11-03-20]

Rev.3

INST(RM)11-03-20

5. Instructing to start removal by Maintenance Utility

(1) <Main Window>

Click the [Chassis] tab in the main window, and click [Remove] and select [Remove Controller

Boards (CTL02/11)]

(2) <Specify Removal Controller Board>

About

“

Forcibly run without safety checks

”

If you check this checkbox and execute the maintenance, the system may go down. Do not

check it unless instructed by the message, the manual or the contact described in the manual.

About

“

Forcibly block

”

If you check this checkbox and execute the maintenance, the system may go down. Do not

check it unless instructed by the contact described in the manual.

Click [Remove].

NOTE: The error list window is displayed if multiple errors are detected by the prior check.

If it is displayed, click the text of

“

Error Code

”

and recover the failures or the

blockade in accordance with the details of the displayed errors.

Содержание DKC910I










































































































































Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды

Hitachi DKC910I, Руководство по установке

Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды