Hitachi DKC910I Скачать руководство пользователя страница 53

Страница: 53 / 138

DKC910I

Hitachi Proprietary

[INST(RM)04-03-210]

Rev.2

INST(RM)04-03-210

15. Removing the rails

(1) Procedure for SBX/UBX

(a) Remove the screw and the loop cable tie from the rear side of right rail.
(b) Remove the screw and the loop cable tie from the rear side of left rail in the same way.

Figure 4-19 Removing Screws

of the rack frame.

(d) Push the rail that is mounted at the right side of the rack frame and remove the Positioning Pin

on the front side of the rail. Then remove the rail from the rack frame.

(e) Remove the left side rail from the rack frame in the same way as

Step (c)

and

Step (d)

(f) Remove the other rails in the same manner.

Figure 4-20 Removal of Slide Rail

Rail

Frame (Front)

Screw

Frame (Rear)

Loop cable tie

Rail

1 Unit
1 Unit

1 Unit

Clip

Positioning Pin

Clip

Positioning Pin

Frame (Front)

Frame (Rear)

Содержание DKC910I










































































































































Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды

Hitachi DKC910I, Руководство по установке

Результаты поиска

Содержание DKC910I

Отзывы:

Бренды по названию

Популярные бренды