Hitachi DH24PB2 Скачать руководство пользователя

Страница: 20 / 39

--- 17 ---

8-3. "Rotation Only" and "Ro Hammering" Changeover Mechanism

The change lever on the Model DH 24PB2 permits quick and easy changeover between the "Rotation Only" and

"Ro Hammering" functions. When operating the change lever, be sure to continue pressing the pushing

button. Armature rotation is transmitted to the second shaft and first gear, and then to the clutch via the spline on

the second shaft spline. Claws on the surface of the clutch engage matching claws on the reciprocating bearing

to convert the rotation into reciprocating motion. The clutch can travel back and forth on the second shaft. Claws

on the surface of the clutch is pressed against on the reciprocating bearing by the force of the clutch spring during

usual operation ("Ro Hammering"). The reciprocating bearing is fitted on the second shaft with some play.

When the change lever is set to the "Rotation Only" ( mark) position, the eccentric pin of the change lever forces

the clutch to move against the pressure of the clutch spring in the direction of the front cap, so that it disengages

from the claws on the reciprocating bearing, and the reciprocating bearing stops rotating on the second shaft.

When the change lever is returned to the "Ro Striking" ( mark) position, the force of the clutch spring

presses the clutch back against the reciprocating bearing so that the claws engage to transmit rotation to the

reciprocating bearing once more.

8-4. "Rotation Only" (no hammering)

The Model DH 24PB2 is equipped with a change lever for changeover between "Ro Hammering" and

"Rotation Only" functions, merely mounting the chuck adapter will not stop the hammering action; it is absolutely

necessary to turn the change lever to the "Rotation Only" setting for drilling or driving screws. Should the change

lever be set to the "Ro Hammering" position when the tool is used for drilling, the hammering action may

cause the drill chuck to be broken or damaged. Sales personnel should carefully ensure that the buyer is

thoroughly advised on this point.

Содержание DH24PB2








































Результаты поиска

Содержание DH24PB2

Отзывы:

Похожие инструкции для DH24PB2

Бренды по названию

Популярные бренды

Hitachi DH24PB2, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание DH24PB2

Отзывы:

Похожие инструкции для DH24PB2

Бренды по названию

Популярные бренды