background image

--- 4 ---

5. SPECIFICATIONS

5-1. Specifications

Capacity

Power source

No-load

Full-load

Weight

Packaging

Standard accessories

3.4 --- 24 mm (1/8" --- 15/16")

AC single phase 50 Hz or 60 Hz

0 to 830 min

-1

2.4 kg (5.3 lbs.)

4.5 kg (9.9 lbs.)

Plastic case

(1) Plastic case 

  • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •          

1

(2) Side handle 

 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

  1

(3) Depth gauge 

 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •      

 1

Voltage, current and input

Enclosure

Full-load blow

0 to 4,600 min

-1

 Housing
 Handle cover
 Gear cover 

• • • • • • • • • • • • •

AC single-phase commutator motor

Type of motor

Model

DH 24PB2

13 mm (1/2")

32 mm (1-1/4")

Voltage (V)

  Current (A)

  Input (W)

110

6.8

120

6.3

220

3.4

230

3.3

240

3.1

720

Rotation speed

Forward:  0 to 1,050 min

-1

, Reverse: 0 to 640 min

-1

Type of switch

Speed control switch with reversing switch

Gun-type handle of main body and side handle

Type of handle

Glassfiber reinforced polyamide resin (green and black)

Glassfiber reinforced polyamide resin (black)

• • • • •

Net*

Gross

Concrete

Steel

Wood

* Weight excludes cord and side handle.

Содержание DH24PB2








































Отзывы: