Hitachi DH24PB2 Скачать руководство пользователя

Страница: 31 / 39

--- 28 ---

B. Additional wiring work

General internal wiring can be accomplished by referring

to paragraphs 9-4 and 9-5-A. The following are special

instructions for switch connection.

(1) Wiring of reversing switch

Insert the lead wire (black) coming from the stator into

the terminal (1) of the reversing switch, and the lead

wire (white) into the terminal (2) as shown in Fig. 21.

Insert the lead wire (brown) coming from the carbon

brush or choke coil into the terminal (3) and the lead

wire (blue) into the terminal (4). After the insertion,

pull each lead wire slightly to check the lead wires do

not come off. To disconnect the lead wires, insert a

small flat-blade screwdriver into the windows near the

terminals and pull out the lead wires.

(2) Wiring of speed control switch

Insert each cord into the terminal 1 and terminal 2

of the speed control switch as shown in Fig. 22 and

tighten the screw (tightening torque: 0.6 0.2 N

•

(6 2 kgf

•

cm, 5.2 1.7 in-lbs.)). Insert the lead wire

(gray) coming from the stator into the terminal M1 and

the lead wire (red) into the terminal M2. Insert each

lead wire (white) coming from the noise suppressor

into the terminal C1 and C2. After the insertion, pull

each lead wire slightly to check the lead wires do not

come off. To disconnect the lead wires, insert a small

flat-blade screwdriver into the windows near the

terminals and pull out the lead wires.

Fig. 18 Wiring of reversing switch

(Stator) (CB or choke coil)

Black

Brown

Blue

White

(Stator)

(CB or choke coil)

Fig. 19 Wiring of reversing switch

(Stator)

(Noise suppressor)

White

Red

Gray

Brown or black

(Cord)

9-6. Insulation Tests

On completion of disassembly and repair, measure the insulation resistance and conduct the dielectric strength

test.

Insulation resistance: 7 M

Ω

or more with DC 500 V megohm tester

Dielectric strength:

AC 4,000 V/1 minute, with no abnormalities 220 V --- 240 V (and 110 V for U.K. products)

AC 2,500 V/1 minute, with no abnormalities 110 V --- 120 V (except U.K. products)

9-7. No-load Current Values

After no-load operation for 30 minutes, the no-load current value should be as follows:

Voltage (V)

Current (A) max.

3.6

110

3.3

120

1.8

220

1.7

230

1.6

240

White

(Noise suppressor)

(Stator)

Blue or white

(Cord)

Содержание DH24PB2








































Результаты поиска

Содержание DH24PB2

Отзывы:

Похожие инструкции для DH24PB2

Бренды по названию

Популярные бренды

Hitachi DH24PB2, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание DH24PB2

Отзывы:

Похожие инструкции для DH24PB2

Бренды по названию

Популярные бренды