manualshive.com logo in svg

Hitachi C28W40TN, Руководство по обслуживанию

Телевизор Hitachi C28W40TN - высококачественный продукт с ярким экраном и четким звуком. Управляйте им с легкостью благодаря подробному Руководству пользователя, которое можно бесплатно скачать на manualshive.com. Погрузитесь в мир качественного просмотра без лишних хлопот с помощью этого удивительного устройства.

Поделиться
Скачать
background image

72

 

Fault Code

Description

0000

The microprocessor was reset due to the microprocessor watchdog. This is most likely
to occurs as a result of electrical disturbance, but may also happen due to a failure of
I001, I002 or I003 (where fitted).

0001

The power good line was activated (taken to ground) whilst the set was powered up.

0002

The protection line was activated (taken to ground) whilst the set was powered up.

0003

Failure of the horizontal deflection. This fault code is set when the horizontal OSD sync
pulse on pin 49 of I001 is missing when the set is powered up.

0004

Failure of the vertical deflection. This fault code is set when the vertical OSD sync pulse
on pin 48 of I001 is missing when the set is powered up.

0005

Timeout of the black current stabilisation when the set was powering up. This will occur
as a result of a failure of the RGB circuits between the TDA9330 (IE02 pins 40-42),
P302, the CRT base PWB and the feedback signal via P302 to IE02 pin 44.

0006

Failure of the microprocessor to communicate on the I2C bus as either/both of the
SDA/SCL signals were shorted to ground or +5V

0007

The set failed to power up after 3 attempts. The reason for this will be evident from the
other fault codes.

0008

The microprocessor had a power on reset, usually as a result of failure of the standby
5V supply or the main power supply shut down (due to overcurrent protection) when the
set was powered up. The count for this fault is incremented when the microprocessor is
reset and is cleared when the TV successfully powers up.

0009

EHT overvoltage (X-Ray protection) detected. This fault occurs as a result of a voltage
greater than 4 volts at the EHT compensation input (pin 4) of IE02.

000a

Flash over detected. This fault occurs as a result of a voltage greater than 2 volts at pin
5 of IE02 (TDA9330).

000b

The microprocessor failed to communicate with the EEPROM (I005) due to a failure of
that device or the I2C bus connections.

000c

The DTT fan failure detection line was activated (taken to ground) for 10 seconds while
the DTT module was powered up (digital models only). This is detected at pin 32 of
I001.

000d

The TV received no signal for 10 minutes when in digital (where appropriate) or RF
modes. This could be a problem with the aerial or a fault in the tuner module or circuitry
around I200.

000e

(Dolby Digital sets only) Internal failure of the Dolby Digital decoder module.

 

 

Codes 01xx indicate a failure of I2C control of a device, where xx identifies that device. The supported codes are as
follows.

0184

The microprocessor failed to control the MSP3410 sound processor (I400).

018a

The microprocessor failed to control the TDA9320 input processor (I200).

018c

The microprocessor failed to control the TDA9330 output processor (IE02).

 

 

Codes 02xx indicate an internal reset of an I2C controlled device, the xx identifies that device. The device codes are the
same as the corresponding 01xx code. The supported codes are as follows.

0284

A power on reset of the MSP3410 sound processor (I400) was detected.

028a

A power on reset of the TDA9320 input processor (I200) was detected.

028c

A power on reset of the TDA9330 output processor (IE02) was detected.

 

 

Codes 0300 are related to the DTT module. These are only applicable to IDTV sets.

0300

The TV microprocessor failed to communicate with the DTT Module via the RS232 link.
This could be due to failure of the DTT power supply, the cable connections between
the TV and DTT modules or a fault internal to the DTT module.

0301

The DTT Module reported a failure of the AV memory.

0302

The DTT Module reported a non-volatile memory failure.

0304

The DTT Module reported a failure of the PAL encoder.

0305

The DTT Module reported a failure of the Front End Demodulator.

0306

The DTT Module reported a failure of the Front End FEC.

0307

The DTT Module reported a failure of the AFE Tuner.

0308

The DTT Module reported a failure of the Altera device (IC400).

0309

The DTT Module reported a failure of the modem.

030a

The DTT Module reported a failure of the smartcard interface.

030b

The DTT Module reported a signal/picture failure.

As stated above, a status value will be stored for each fault. The status values consist of the following information: -
A count of the number of times that the fault has been detected. This counts up to 9 and stops. This number will only be increased
once every time the TV is powered up.
Indication of how recent the fault was. A value of 7 means the fault is the most recent, to have occurred, value of 0 means the fault
is the least recent.

Содержание C28W40TN











































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для C28W40TN

Panasonic Viera TH-65PZ750 Manual De Instrucciones preview
Viera TH-65PZ750
Бренд: Panasonic Страницы: 59
Daewoo DTA-14C4TFF Service Manual preview
DTA-14C4TFF
Бренд: Daewoo Страницы: 49
Daewoo DTH-28 Setup Manual preview
DTH-28
Бренд: Daewoo Страницы: 18
aiko NP-42H5 Service Manual preview
NP-42H5
Бренд: aiko Страницы: 94
TCL 65C835 Operation Manual preview
65C835
Бренд: TCL Страницы: 21
Westinghouse aspect ratio Manual preview
aspect ratio
Бренд: Westinghouse Страницы: 1
Denver LDS-4371 Quick Start Manual preview
LDS-4371
Бренд: Denver Страницы: 12
Samsung UE85HU7590L E-Manual preview
UE85HU7590L
Бренд: Samsung Страницы: 241
Toshiba 26HF66 Specifications preview
26HF66
Бренд: Toshiba Страницы: 2
Philips 21PT2321 Specification Sheet preview
21PT2321
Бренд: Philips Страницы: 2
Philips 21PT2684 Brochure preview
21PT2684
Бренд: Philips Страницы: 19
Philips 21PT2264 Specifications preview
21PT2264
Бренд: Philips Страницы: 19
Philips 21PT2110 Operating Instructions Manual preview
21PT2110
Бренд: Philips Страницы: 28
Philips 21PT2217/94 Service Manual preview
21PT2217/94
Бренд: Philips Страницы: 35
Philips 21PT2152 Operating Instructions Manual preview
21PT2152
Бренд: Philips Страницы: 36
Haier TDC1314S User Manual preview
TDC1314S
Бренд: Haier Страницы: 34
Haier TDC1354AD Service Manual preview
TDC1354AD
Бренд: Haier Страницы: 16
Haier LT32R1 User Manual preview
LT32R1
Бренд: Haier Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды