Hitachi Aloka Medical ASU-1003 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

Hitachi Aloka Medical ASU-1003 Скачать руководство пользователя страница 26

-20-

MN1-5008 Rev. 7

4-4. Connecting to the ultrasound diagnostic instrument

The lock lever of the connector moves over the range shown in the figure

at right.

Align the ○ mark with the LOCK or RELEASE position and lock or

release the electronic probe connecting socket of the diagnostic instrument

( probe connector ).

Connect the scanner to the probe connector by following the procedure

below.

• Connection procedure

The scanner is connected when in one of the following states.

• The power switch is set to OFF.

• The image displayed on the ultrasound diagnostic instrument is

frozen.

Before inserting the scanner into the probe connector, check that the

connector pins are not bent.

1. Turn the connector lock lever to align the ○ mark on the lever with the

RELEASE position.

2. Firmly insert the connector into the probe connector on the ultrasound

diagnostic instrument.

3. Turn the lock lever clockwise by 1/4 turn until the ○ mark is aligned

with the LOCK position.

4. Check that the connector is firmly inserted into the probe connector on

the instrument.

5. Connect the cable for driving to the upper part of the connector box.

This completes connection of the scanner.

Caution

If there is resistance when trying to turn the lock lever when connecting the connector, do not

forcibly try to connect it. Instead, correctly perform the steps for connecting the connector and

firmly insert it into the probe connector.

Forcibly turning the lever may damage the connector and the probe connector.

Lock lever

Movable

range

○ mark

LOCK

RELEASE

RELEASE

LOCK

Small connector

«
...
24
25
26
27
28
...
»

Содержание ASU-1003













































Отзывы:

Нет отзывов