10
HSK2411202016 | Dynamic Terminal Ku 8X8 V2 | Quick Start Installation Guide
Varoitus: Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Attention: Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Warnung: Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle anschließen.
Avvertenza: Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Advarsel: Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Aviso: Leia as instruções de instalação antes de ligar o sistema à sua fonte de energia.
¡Advertencia!:Ver las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
Varning!: Läs installationsanvisningarna innan du kopplar systemet till dess strömförsörjningsenhet
.
Power Supply Circuit Warning
WARNING: Care must be given to connecting units to the supply circuit so that wiring is not overloaded.
Waarschuwing: Let erop dat de toestellen op voedingscircuits worden aangesloten zonder het vermogen van de
bed rading te overschrijden.
Varoitus: Laiteyksiköt on yhdistettävä huolellisesti syöttöpiiriin niin, että johdot eivät ole ylikuormitettuja.
Avertissement: Veillez à bien connecter les unités au circuit d'alimentation afin de ne pas surcharger les
connections.
Achtung: Beim Anschließen der Geräte an das Stromnetz ist darauf zu achten, daß die Schaltverbindungen nicht
überlastet werden.
Avvertenza: Fare attenzione quando si collegano le unità al circuito di alimentazione, per non sovraccaricare i
cablaggi.
Advarsel: Vær nøye med å koble enheter til strømforsyningskretsen slik at ledningene ikke overbelastes.
Aviso: Deverá ter precaução ao ligar unidades ao circuito de fornecimento de energia, para não sobrecarregar a
instalação.
¡Atención!: Poner mucho cuidado al conectar los equipos al circuito de alimentación a fin de no sobrecargar el
cableado.
Varning!: Var noga vid anslutning av enheter till matarströmkretsen så att ledningarna inte överbelastas.
Agency Compliance
For detailed information on standards, see
https://www.hiskysat.com/Product Documentation.
Pour des informations détaillées sur les normes, voir
https://www.hiskysat.com/Product Documentation
FCC Compliance
Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
47CFR Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. The equipment uses, generates, and radiates radiofrequency energy. If
the equipment is not installed and used by the instructions, it may cause harmful interference to radio
communications. There is also no guarantee that interference will not occur in a particular installation. To
determine if the equipment is interfering with radio or television reception, remove or apply power to the
equipment and see if the interference goes away, or returns, when the unit is off or on.
To meet FCC requirements, only peripherals, such as computer input/output devices, terminals, and printers
certified to comply with the Class B limits, may be attached to this device. Operation with non-certified
peripherals is likely to result in interference to radio and TV reception.
To meet FCC requirements, shielded cables are required to connect the device to a personal computer,
peripheral, or other Class B certified device.
WARNING: Modification of this equipment without written authorization from hiSky may result in this
equipment no longer complying with FCC requirements for Class B digital devices. In that event, the rights
